masacre Posted June 26, 2007 Share Posted June 26, 2007 hello I write to see if there is some solution to my problem or can come with the RMA description from hardware problem Mainboard Abit AT8 32x Memory 4 x xpert 512 mb module 3200c2 HD 2x 250 GB raid 0 WD VGA ATI AIW x1900 BBA power supply Vantec Sthealth 620w max. corsair Water cooling nautiluss Monitor IBM P260 21" - my system does not initiate with these memories or a single one or both single or dual chanel and proven with other plates mothers and processors and nothing sige equal the memories to initiate display with normality but the system throws read error of memory in boot (C1 error on display mainboard) My bad pair memories XMS 3202 v 1.1 0509043-1 100273690 TwinXP1024-3200c2 8 70584 00524 7 excuses by my badly English my native language are the Spanish Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted June 26, 2007 Corsair Employees Share Posted June 26, 2007 Please make sure that you have the latest Bios version and then load setup/optimized defaults and set the Dim Voltage to 2.7 volts and then set the timings manually to the tested settings for the specific module you have, and then test the module/'s one at a time with http://www.memtest.org! If you still get errors, please follow the link in my signature “I think I have a bad part!” and we will be happy to replace them or it! However, if you get errors with both modules that would suggest some other problem and I would test them in another system or MB to be sure. In addition, with 4 modules on this MB you would need to set the memory frequency at DDR333 with this MB. Link to comment Share on other sites More sharing options...
masacre Posted June 26, 2007 Author Share Posted June 26, 2007 HELLO thanks to respond quickly. good if use completes bios for my mothrboard (version. 1.2) and e proven the values by defect, in addition and tried to initiate the system just by the pair that gives to problems and nothing me, also and tried to initiate with 1 memory of the bad pair and do not initiate either. the LED indicates activity but the system does not reach to initiate bios. if before tapeworm the four 333 modules working to 2-3-3-6 2t mhz during long time and no east problem weekend freeze the single system and probe with a pair separately, a pair I work without problems and the described pair just I do not leave boot the PC. probe in another plate mother a together MSI and the same does not initiate system either or separately note I do not reach to see post of bios so nor to speak of memtest :mad: Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted June 26, 2007 Corsair Employees Share Posted June 26, 2007 I am sorry but I don't understand what you have posted. Please post it in your native Language and tell me what it is and I will get it translated. But just follow the steps and test the modules one at a time with http://www.memtest.org if one fails and the rest pass just see if the reseller will help you get them replaced. Link to comment Share on other sites More sharing options...
masacre Posted June 27, 2007 Author Share Posted June 27, 2007 disculpas . tengo la ultima version de la bios de mi placa madre (* version 1.2) configure mi sistema con 2.7 Vmem 2-3-3-6 2t 2 modulos x 512 MB no inicia el sistema . instale solo una memoria y probe iniciar sistema . tampoco me da post ninguna de las 2 memorias inicia la placa madre juntas o por separado probe con otras placas madres y lo mismo me es imposible probar memtest ya que ni si quera puedo ver el post de inicio de placa madre . el otro par de memorias funciona perfectamente .. Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted June 27, 2007 Corsair Employees Share Posted June 27, 2007 excuses. I have completes version of the bios of my plate mother (* version 1.2) Vmem 2-3-3-6 forms my system with 2,7 2t 2 modules x 512 MB it does not initiate the system. install single a memory and probe to initiate system. it does not give post either me no of the 2 memories initiates the together plate separately mother or probe with other plates mothers and the same it is impossible to me to prove memtest since nor if quera I can see post of beginning of plate mother. the other pair of memories works perfectly. f I understand you correctly then you have some other problem and I would suggest asking the reseller to help you trouble shoot the problem. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.