Jump to content
Corsair Community

Mismatch in TWIN2X2048-6400C4 module


Recommended Posts

I recently bought the above memory sticks in Denmark however there

seems to be a mismatch as one of the sticks seems tobe a 6400 module

asper below info retrieved from the modules thru a program called PC Wizard 2007 and can advise that same was reported by other utilities aswell:

 

Information SPD EEPROM (DIMM0) :

Manufacturer : Corsair

Part Number : CM2X1024-6400

Serial Number : Unspecified

Type : DDR2-SDRAM PC2-6400 (399 MHz)

Format : Regular UDIMM (133,35 x 3)

Size : 1024 MB (0 rows, 2 banks)

Module Buffered : No

Module Registered : No

Module EPP : No

Width : 64-bit

Error Correction Capability : No

Max. Burst Length : 0

Refresh : Reduced (.5x)7.8 µs, Self Refresh

Voltage : SSTL 1.8v

Prefetch Buffer : 4-bit

Manufacture : Week 29 of 2006

Supported Frequencies : 270 MHz, 400 MHz

CAS Latency (tCL) : 4 clocks @270 MHz, 5 clocks @400 MHz

RAS to CAS (tRCD) : 4 clocks @270 MHz, 5 clocks @400 MHz

RAS Precharge (tRP) : 4 clocks @270 MHz, 5 clocks @400 MHz

Cycle Time (tRAS) : 13 clocks @270 MHz, 18 clocks @400 MHz

Min TRC : 15 clocks @270 MHz, 22 clocks @400 MHz

 

Information SPD EEPROM (DIMM2) :

Manufacturer : Corsair

Part Number : CM2X1024-6400C4

Serial Number : Unspecified

Type : DDR2-SDRAM PC2-6400 (399 MHz)

Format : Regular UDIMM (133,35 x 3)

Size : 1024 MB (0 rows, 2 banks)

Module Buffered : No

Module Registered : No

Module EPP : Yes

Width : 64-bit

Error Correction Capability : No

Max. Burst Length : 0

Refresh : Reduced (.5x)7.8 µs, Self Refresh

Voltage : SSTL 1.8v

Prefetch Buffer : 4-bit

Manufacture : Week 29 of 2006

Supported Frequencies : 270 MHz, 400 MHz

CAS Latency (tCL) : 4 clocks @270 MHz, 5 clocks @400 MHz

RAS to CAS (tRCD) : 4 clocks @270 MHz, 5 clocks @400 MHz

RAS Precharge (tRP) : 4 clocks @270 MHz, 5 clocks @400 MHz

Cycle Time (tRAS) : 13 clocks @270 MHz, 18 clocks @400 MHz

Min TRC : 15 clocks @270 MHz, 22 clocks @400 MHz

 

EPP Profile Type : Full Performance

Profiles : 2

Voltage Level (P1) : 0V

Address Command Rate (P1) : 0T

Cycle Time (P1) : 0ns @1,#INF MHz

CAS Latency (tCL) (P1) : 0 clocks

Voltage Level (P2) : 0V

Address Command Rate (P2) : 0T

Cycle Time (P2) : 0ns @1,#INF MHz

CAS Latency (tCL) (P2) : 0 clocks

 

The sticks are labelled identically being 6400C4

This is clearly a warranty issue but can i ask my dealer

to replace them or must i go thru an RMA which presumably will mean

that i will be unable to use my pc for atleast a month or more ?

 

Any advice will be highly appreciated.

 

Kind regards,

 

Stan

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...