MichaelO Posted January 12, 2007 Share Posted January 12, 2007 I have recently stared getting the blue screen of death. I have tested my Ram (2 sticks - CMX1024-3200C2) with the tool called CheckIt Diagnostics. Each stick of Ram passed by itself however, when both installed it fails. HELP!! It's getting worse. Gigabyte GA K8NS-939-ULTRA bios version F-10 AMD 64 3500+ HT Frequency Ratio [5x] CPU Clock [200] Hammer fid [Auto] Current DDR Speed [400] DDR Clock / Timing Mode [Auto] x CPU/DDR Clock Ratio 2/2 DDR Speed 400 x DDR Timing Auto x Cas# latency (TCL) 3 X Min Ras active time 8T x Ras# to cas# delay 3T x Row Percentage Time 3T x Row to Row delat 2T x Row time cycle 11T x Row refresh cyc time 13T x Read-Write time 4T x TWR 3 bus cycle x twtr 2 bus cycle x Refresh Rate 200 MHZ, 7.8us x Read Preamble Value 5.5ns x Async Latency Value 7ns DDR voltage [Normal]image002.bmp Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted January 12, 2007 Corsair Employees Share Posted January 12, 2007 Please load setup/optimized defaults and then set the Dim Voltage to 2.7X volts (+.2 Volts W/Giga-Byte) and then set the timings manually to the tested settings for the specific module you have, XMS3200C2 Cass 2-3-3-6 for example or if you have Value Select "BY SPD" and then test the module/'s one at a time with http://www.memtest.org! If you still get errors, please follow the link in my signature “I think I have a bad part!” and we will be happy to replace them or it! However, if you get errors with both modules that would suggest some other problem and I would test them in another system or MB to be sure. Link to comment Share on other sites More sharing options...
MichaelO Posted January 12, 2007 Author Share Posted January 12, 2007 No problem.. Only question I have is where do I change the settings "2-3-3-6T" at? x DDR Timing Auto x Cas# latency (TCL) 3 (Is this the 2??) X Min Ras active time 8T x Ras# to cas# delay 3T (Is this the first 3??) x Row Percentage Time 3T (Is this the second 3??) x Row to Row delat 2T x Row time cycle 11T x Row refresh cyc time 13T x Read-Write time 4T (Is this the 6T??) x TWR 3 bus cycle x twtr 2 bus cycle x Refresh Rate 200 MHZ, 7.8us x Read Preamble Value 5.5ns x Async Latency Value 7ns Sorry but there are so many places :( Link to comment Share on other sites More sharing options...
Corsair Employees RAM GUY Posted January 13, 2007 Corsair Employees Share Posted January 13, 2007 You can find the settings from the link in my signature! Memory Voltage should be set to +.3 Volts as well. x DDR Timing Auto x Cas# latency (TCL) 2 (Is this the 2 YES??) X Min Ras active time 6T x Ras# to cas# delay 3T (Is this the first 3 YES ??) x Row Percentage Time 3T (Is this the second 3 YES ??) x Row to Row delat 2T x Row time cycle 11T x Row refresh cyc time 13T x Read-Write time 4T (Is this the 6T?? NO SHOULD BE 5 thou) x TWR 3 bus cycle x twtr 2 bus cycle x Refresh Rate 200 MHZ, 7.8us x Read Preamble Value 5.5ns x Async Latency Value 7ns Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.