Jump to content
Corsair Community

Abit kn8 sli with Corsair TWINX1024-4400C25


Stoopidwog

Recommended Posts

just received my kn8 sli and plug all my stuff in....and can't make it through a windows installation without a BOD or restart. If i take out one of the memory sticks ....system becomes stable.

 

specs:

Abit kn8 sli (1.9 bios)

Amd 3200+

Corsair TWINX1024-4400C25

Antec 550watt true power

WD 250gig sata

Inno3d 7600gt

 

have increased ram voltages and cpu voltages but hasn't helped. Only seems to happen when ram is in dual channel....single channel runs fine

 

all components ran fine few hours ago in a different motherboard

Link to comment
Share on other sites

thanks for the response ....ok here goes....

 

**soft menu**

 

Cpu Core Voltage - 1.4v

DDR Ram Voltage - 2.8v

DDR Ref Voltage - -60mv

Nforce4 Voltage - 1.5

Hypertransport Voltage - Default

 

**dram configuration**

 

Dram Timing Selectable - By SPD

DRAM Clock - DDR400

CAS Latency Time - 2.5

Row Cycle Time - 11 Clocks

Row Refresh Cycle Time - 14 Clocks

Min. RAS# Active Time - 8 Clocks

RAS# to CAS# delay - 4 Clocks

RAS# Precharge Time - 4 Clocks

RAS# to RAS# Delay - 2 Clocks

Write Recovery Time - 3 Clocks

Write to Read Delay - 2 Clocks

Read to Write Delay - 4 Clocks

DRAM Command Rate - AUTO

Read Preamble value - AUTO

Max. Async Latency value - AUTO

Bank Interleaving - Enabled

Burst Length - 4 Beats

DRAM Drive Strength - Normal Drive

Force 64-bit mode always - Enabled

R/W Queue Bypass Counter - 8

Bypass Max - 4

Idle Cycle Limit(ILD_LMT) 16 Cycles

Dynamic Idel Cycle Count.Enabled

MTRR mapping mode - Continuous

32 bit Dram Memory Hole - Auto

Link to comment
Share on other sites

  • Corsair Employees

Please try these settings and test the system with http://www.memtest.org.

Soft Menu:

CPU Freq: 200 Mhz

Cpu Core Voltage - 1.4v

DDR Ram Voltage - 2.8v

DDR Ref Voltage - -60mv

Nforce4 Voltage - 1.5

Hypertransport Voltage - Default

 

**dram configuration**

 

Dram Timing Selectable - Manual/User Define

DRAM Clock - DDR400

CAS Latency Time - 2.0

Row Cycle Time - 11 Clocks

Row Refresh Cycle Time - 14 Clocks

Min. RAS# Active Time - 6 Clocks

RAS# to CAS# delay - 3 Clocks

RAS# Precharge Time - 2 Clocks

RAS# to RAS# Delay - 2 Clocks

Write Recovery Time - 3 Clocks

Write to Read Delay - 2 Clocks

Read to Write Delay - 4 Clocks

DRAM Command Rate - AUTO

Read Preamble value - AUTO

Max. Async Latency value - AUTO

Bank Interleaving - Enabled

Burst Length - 4 Beats

DRAM Drive Strength - Normal Drive

Force 64-bit mode always - Enabled

R/W Queue Bypass Counter - 8

Bypass Max - 4

Idle Cycle Limit(ILD_LMT) 16 Cycles

Dynamic Idel Cycle Count.Enabled

MTRR mapping mode - Continuous

32 bit Dram Memory Hole - Auto

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...