D-Day Posted January 3 Share Posted January 3 7000D Custom Water loop GPU and CPU 4 16g rgb corsair ram. I am using 2 Commander Core XT's because of length of wire in the large case with lower fans attached to one and the upper fans attached to the other. In ICUE software I can't figure out how to order the fans for full case effect...2 front fans on one and 2 on the other. If you could point me to videos or another post that would be great. Thanks Link to comment Share on other sites More sharing options...
Kontio Posted January 3 Share Posted January 3 Moin .... wenn der Core XT richtig platziert wurde, passen alle drei Frontlüfter an die Core XT ....Auf dem Bild ist zu sehen, dass ich auch zwei Core XT verwende . An dem in der linken Ecke kommen die drei Front, und die drei oberen Lüfter dran. An den unteren Core XT , kommen die vier Seitenlüfter, der hintere Lüfter und die Hydro X Kühler .... 1 Link to comment Share on other sites More sharing options...
c-attack Posted January 3 Share Posted January 3 3 hours ago, D-Day said: am using 2 Commander Core XT's because of length of wire in the large case with lower fans attached to one and the upper fans attached to the other. If you are using two Commander XTs (or two of any lighting controller), then you have two lighting groups. You cannot easily program a moving effect to jump between controllers. It seems unlikely you have just 4 fans. How are the fans arranged? 1 Link to comment Share on other sites More sharing options...
D-Day Posted January 3 Author Share Posted January 3 Front = 360 radiator at the top 4 QL120's with one in the HD bay all pulling air in. Side = Same as front Top = 1 QL120 at the front to make room for the side radiator and 2 140 AirGuide non RGB (stock) at the back All blowing air out Back = 1 140 AirGuide blowing air out. Thanks Link to comment Share on other sites More sharing options...
D-Day Posted January 3 Author Share Posted January 3 Kontio, Where are you routing the lower front 2 fan cables? I only have enough to mount the XT at the bottom. D Link to comment Share on other sites More sharing options...
D-Day Posted January 3 Author Share Posted January 3 Kontio, Very nice cabling. D 1 Link to comment Share on other sites More sharing options...
D-Day Posted January 3 Author Share Posted January 3 c-attack, Would a commander pro with 2 Lighting Node Core's work? or would the Node's be two lighting groups? D Link to comment Share on other sites More sharing options...
c-attack Posted January 3 Share Posted January 3 (edited) 2 hours ago, D-Day said: Would a commander pro with 2 Lighting Node Core's work? or would the Node's be two lighting groups? It will still be two lighting groups — LED channel 1 and LED channel 2. On the Pro controllers each RGB Lighting hub is a channel/group. You are limited to 6 fans per group/channel. What are you hoping to do with effects? Most users want to run the unique LL/QL presets like pong, gate, ping, etc. and you can’t do this across multiple controllers. You must set the effect for each one and it will run from fan 1 to X on that controller only. For intra fan effects like rainbow wave, rotary stack, etc., this does not matter snd you simply set the effect once on each controller. It will be the same on every fan. It is possible to manually program a wave to start on controller 1, fan 1and pass through the first series while the second waits, and then vice versa. However, it’s tedious to set up and requires some basic calculations for speed and tail. Edited January 3 by c-attack 1 Link to comment Share on other sites More sharing options...
Kontio Posted January 5 Share Posted January 5 On 3.1.2023 at 20:41, D-Day said: Kontio, Wo verlegen Sie die unteren vorderen 2 Lüfterkabel? Ich habe nur genug, um den XT unten zu montieren. D Also bei meinem 7000 X RGB sind die Kabel der vorderen drei 140er Lüfter von Haus aus ( also schon im Gehäuse dabei) mit Verlängerungskabeln versehen. Ich habe die nur gegen QL Lüfter ausgetauscht. Aber wie gesagt, die Kabel sind dadurch lang genug ( auch der untere Lüfter) das die bei mir an den im Bild oberen Core XT angeschlossen werden können .... Link to comment Share on other sites More sharing options...
Kontio Posted January 5 Share Posted January 5 On 3.1.2023 at 20:42, D-Day said: Kontio, Sehr schöne Verkabelung. D Danke , ist noch nicht ganz Fertig 🙂 Link to comment Share on other sites More sharing options...
Kontio Posted January 5 Share Posted January 5 (edited) Moin .... Habe mal eben fix ein Bild von den Lüfterkabeln gemacht . So lang kommen die aus dem Gehäuse incl. der Verlängerung . Selbst das von dem unteren Lüfter ist noch zu lang für den oben Core XT 😇 Edited January 5 by Kontio Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now