Jump to content
Corsair Community

ICUE会使K95XT失灵卡住,键盘重置后大概2-3天会重复发生


Recommended Posts

There is no way to exclude the K95XT from the CUE devices list. However since that model has onboard storage, you can save relatively simple lighting patterns and actions to the KB memory, then set CUE not to run on start up. 
 

However, the consistent freezing is not overly common. Most users who experience this have other RGB or peripheral control programs that become entangled with CUE. Is there another program that might be causing this?  It’s also possible you need that program so then you are back to using the K95XT memory instead of CUE. 

Link to comment
Share on other sites

8 hours ago, Wangxxxlu said:

有什么办法解决,或者不让ICUE控制键盘

c-attack说的方法是唯一可已解决你的问题。我的哥们也是有类似问题。

Link to comment
Share on other sites

20小时前,c-attack 说道:

无法从 CUE 设备列表中排除 K95XT。 但是,由于该模型具有板载存储,您可以将相对简单的照明模式和动作保存到 KB 内存,然后将 CUE 设置为在启动时不运行。
 

然而,持续的冻结并不太常见。 大多数遇到这种情况的用户都有其他 RGB 或外围控制程序与 CUE 纠缠在一起。 是否有其他程序可能导致此问题? 也有可能您需要该程序,因此您将重新使用 K95XT 内存而不是 CUE。 

大哥  风扇的转速是否能保存再板载内存里,用的core xt

Link to comment
Share on other sites

Do you have a Commander Core XT fan/RGB controller too?  
 

RGB Lighting - Go to “Hardware Lighting” (might be slightly different name with language localization).  Choose a preset. That is the non-CUE lighting state. 
 

 

 

Fan speed - You need to use a 10K thermistor or temperature probe. There should have been one in the Commander Core XT box, but if not they are inexpensive and any brand or type should work — it’s just a wire with flat sensor end.
 

The best place for that sensor end is usually at the rear exhaust, inside or outside the case. The exhaust air temperature is the best measure of internal case temperature and if you need more or less fan speed. The tricky part is learning your normal temperature operating range, but you can you can use the Corsair AIO liquid temp curve as a base. 
 

Go to “cooling” on the Commander Core XT. Click + to create a new custom curve. Graph appears below. Go to the lower right corner and click one of the shape tools. Then change the sensor choice to “Commander Pro XT Temp #1”. That is the sensor wire value. You can move the data points on the graph as needed. 
 

This works without CUE because the 10k sensor data is native to the controller. It doesn’t need CUE’s CPUID SDK to fetch the data from the motherboard. I know this seems like a lot, but it is what I recommend for everyone even when they are running CUE. Using CPU or GPU temp makes the fans very erratic and just like if you were using a fan on yourself, a relatively steady and consistent air flow is better for managing internal case temperature.  This fan curve is automatically stored to the controller. You do not need to actively save it like most other data. It will save the curve if you pick GPU or motherboard temperature as the sensor choice, but when you exit CUE the data stops and the fan either freezes or goes to maximum. 

Link to comment
Share on other sites

于 2022 年 4 月 10 日下午 7:51,c-attack 说道:

您也有 Commander Core XT 风扇/RGB 控制器吗?
 

RGB 照明 - 转到“硬件照明”(名称可能与语言本地化略有不同)。 选择一个预设。 即非CUE照明状态。
 

 

 

风扇速度 - 您需要使用 10K 热敏电阻或温度探头。 Commander Core XT 盒子里应该有一个,但如果不是,它们很便宜,任何品牌或类型都可以使用——它只是一根带有扁平传感器端的电线。
 

该传感器端的最佳位置通常是在外壳内部或外部的后排气口。 排气温度是内部外壳温度的最佳衡量标准,如果您需要或多或少的风扇速度。 棘手的部分是了解您的正常温度工作范围,但您可以使用 Corsair AIO 液体温度曲线作为基础。
 

转到 Commander Core XT 上的“冷却”。 单击 + 以创建新的自定义曲线。 图表如下所示。 转到右下角并单击其中一个形状工具。 然后将传感器选项更改为“Commander Pro XT Temp #1”。 那是传感器线值。 您可以根据需要移动图表上的数据点。
 

这在没有 CUE 的情况下工作,因为 10k 传感器数据是控制器的本地数据。 它不需要 CUE 的 CPUID SDK 从主板获取数据。 我知道这看起来很多,但这是我向每个人推荐的,即使他们正在运行 CUE。 使用 CPU 或 GPU 温度会使风扇非常不稳定,就像您在自己身上使用风扇一样,相对稳定和一致的气流更适合管理内部机箱温度。 该风扇曲线会自动存储到控制器中。 您不需要像大多数其他数据一样主动保存它。 如果您选择 GPU 或主板温度作为传感器选项,它将保存曲线,但是当您退出 CUE 时,数据停止并且风扇冻结或达到最大值。 

大兄弟 我有一个猜想就是我之前一个连接线是插在USB3.2 GEN1 5GBPS的口子上的另一个是usb2.0上,会不会是电流过大或小的原因,但是我的主板只有USB2.0和3.2的端口,而键盘要求USB3.0 5VDC 900MA的端口,那我应该插在哪个端口上。

Link to comment
Share on other sites

Corsair devices need a USB 2.0 motherboard connection, however most should work with a USB 2->USB 3 converter cable.  This may be necessary if you are using 3 or more Commander Core, Commander XT, or LCD pump top devices.  Most other users will use a powered USB 2.0 hub to help make up for the lack of motherboard ports.  This is an inexpensive device that uses one SATA connection for power and typically provides 3-4 USB 2 ports.  Any brand should work.  

Link to comment
Share on other sites

  • 3 weeks later...
On 4/10/2022 at 12:51 AM, ahfoo said:

c-attack说的方法是唯一可已解决你的问题。我的哥们也是有类似问题。

大哥 我找到原因了 可能是电路板下面灰尘太多了 我整个拆开清理了一下就正常了

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share

×
×
  • Create New...