Jump to content
Corsair Community

Need Commander Pro diagram for my setup


Titan777
 Share

Recommended Posts

Hi guys,

 

I hope this is the correct forum.

I would like help to set up my fans, etc.

 

  • 1 Hydro H115i that I swapped it's two 140ML fans with 140LL fans.
  • 2 additional 120LL fans in front of the 500D RGB case and 1 120LL fan on back.
  • Corsair HX750i.
  • Corsair RGB Led Lighting PRO with Lighting Node Pro.

 

Total is 6 LL fans

1 Led lighting pack

1 i Power supply.

 

I also have Commander Pro and I think 2 USB fan hubs.

 

Please advise what is the best diagram to connect all of them?

 

Thank you! :biggrin:

Edited by Titan777
Link to comment
Share on other sites

Hi guys,

 

I hope this is the correct forum.

I would like help to set up my fans, etc.

 

  • 1 Hydro H115i that I swapped it's two 140ML fans with 140LL fans.
  • 2 additional 120LL fans in front of the 500D RGB case and 1 120LL fan on back.
  • Corsair HX750i.
  • Corsair RGB Led Lighting PRO with Lighting Node Pro.

 

Total is 6 LL fans

1 Led lighting pack

1 i Power supply.

 

I also have Commander Pro and I think 2 USB fan hubs.

 

Please advise what is the best diagram to connect all of them?

 

Thank you! :biggrin:

A Commander Pro has 6 x 3/4-pin fan ports and 2 x USB 2.0 headers.

 

As for the diagram, have a look at Zotty's CORSAIR RGB Hardware and iCUE Eco-System FAQ and scroll down to the diagram "Corsair RGB Fan & Commander Pro Setup."

Link to comment
Share on other sites

assuming you have the H115i Pro...

 

then this one suites you... the only thing i would change is the 2 fans on your radiator, which need to be powered (make them spin) by the h115 (this ensures correct operation of your cooling system regardless of other hardware/software)

 

 

http://i.imgur.com/XSDWsnel.png

 

Thanks! I have the H115i RGB Platinum 280mm but I have changed its ML140 fans with LL140 fans to match the build and case.

 

Does your diagram still work for me?

I also have Corsair LED stirps with the Lighting Node Pro:

 

CM000CS_159504_800x800.jpg

 

Do I need to connect the HX750i USB to the motherboard or to the Commander Pro?

Link to comment
Share on other sites

http://i.imgur.com/ICBYkWkl.png

 

This is exactly what I have, just swapped the H115i RGB Platinum ML fans with new LL fans.

I read that I should not connect the AIO LL fans to the CoPo, only to the Fan Hub. Is that correct?

And my power supply is HX750i.

 

Do I still connect everything according to this diagram? I wonder if the H115i shouldn't go to any hub, just directly to the commander pro as shown?

 

There's no need to use my Lighting Node Pro?

Edited by Titan777
Link to comment
Share on other sites

the h115i platinum is self contained.. runs its own fans for both speed and rgb. no hub required buddy.. install and run as its manual says ;).. and the rest of that diagram is fine ;).. its one of mine isnt it?? lol. i have made soooo many its hard to keep up hahaha

 

PSU and AIO may aswell be connected to the CoPro dude...

 

you are good to go mate

Edited by Zotty
Link to comment
Share on other sites

the h115i platinum is self contained.. runs its own fans for both speed and rgb. no hub required buddy.. install and run as its manual says ;).. and the rest if that diagram is fine ;).. its one of mine isnt it?? lol. i have made soooo many its hard to keep up hahaha

 

PSU and AIO may aswell be connected to the CoPro dude...

 

you are good to go mate

 

Thanks bro. I think it's all working correctly.

 

Why does it take a long time for the ICUE to show the CoPro fans?

Edited by Titan777
Link to comment
Share on other sites

whats a long time dude? and when is this happening?

 

Suddenly I hear the fans noise increase, I go into the ICUE to see the rpm's and nothing shows up, only voltages.

It took 20 minutes for it to show up and once it did, the fans were back to being silent.

This is very weird, is it working properly?

Edited by Titan777
Link to comment
Share on other sites

That's normally indicative of a conflict. Are you running HWInfo? Or have you run it before and installed the resident driver (the default)?

 

I think I know what happens. The commander pro suddenly disconnects. I can hear the USB sound notification when it happens and the fans suddenly increase rpm and the CoPro doesn't show the fans anymore.

 

I have Gigabyte X570 Master.

Link to comment
Share on other sites

 Share

×
×
  • Create New...