Jump to content
Corsair Community

Ram Problem - Rma Request


Recommended Posts

my system frequently crash in game and occasionally with my internet browser

i have Twinx 1024-3200LLPT


- i try with Bios defaut settings, and manually with 2/3/2/6 timings @ 2,75v,

- i try the 2 dual slot of my motherboard,

- i try memtest => errors


P4E 2,8Ghz - Asus P4P800Dlx(bios 1019) - Geforce FX5900XT - MAxtor Sata 160go - Audigy 2zs


sorry for my english , try to answer me with simple words ...

thank you for your help

Link to comment
Share on other sites

  • Corsair Employees

Please make sure that you have the latest BIOS for your MB and load Setup/optimized default settings, and try the following BIOS settings;

TwinX1024 or TwinX512-3200LL

Advanced/Jumper Free

AI over clocking: Manual

CPU Freq: 200

DRAM Clock: 400 MHz

Memory or Dim Reference voltage: 2.75 Volts

System performance: AUTO

AGP Voltage: Default *unless you have ATI (9200 or 9600) or NVIDIA (5200 or 5700) then 1.6 Volts suggested!*


Configure Dram timing by SPD: Disabled/User define

SDRAM CAS Latency: 2T

SDRAM RAS to CAS Delay (tRCD): 3T

SDRAM Row Precharge (tRP): 2T

SDRAM Active to Precharge Delay (tRAS): 6T

SDRAM Burst Length: 8

Memory Acceleration Mode: Auto

USB Legacy Support: Disabled

All other settings should be set to default settings!

Then please test them one at a time with http://www.memtest.org and let’s make sure it's not some other issue! I would run the test for at least 2-3 passes to be sure!

Link to comment
Share on other sites

i have the latest bios version, and i already test with this settings with no o/c, fsb 200 1:1

Dram CAS Latency : 2

Dram RAS Precharge : 2

Dram RAS to CAS Delay : 3

Dram Precharge Delay : 6

Dram Burst Length : 8

Dram Idle Timer : Auto

Dram Refresh Mode : Auto

Memory Acceleration Mode :Auto


Dram Frequency : 2,75v

AGP VDDQ Voltage : 1,50v


memtest 3.2 and 1.20+ cd boot version makes errors on 3th pass


i have tested long time searching the cause of my system instability "sufficiently" to be sure and posting here


my system would seem to be stable only with SPD auto timings at 2/4/4/8


i don't test them separately, twinxmemory should not fonction by pair ?

Link to comment
Share on other sites

ok, i have tested the slots


my first dual slot seems to be dead


slot B2 with part1 : no errors 5 pass run 60 min

slot B4 with part2 : no errors 4 pass run 47 min

no test for the moment in dual mode in slots B


Maybe the source of problem was the Dram Burst set to défaut : 4?


i actually run on the 2th dual slot with 2/3/2/6 / 8 @2,75v and everything seems to be OK, i'll try 6 pass memtest later to confirm


i hope that my computer will be stabe now, still thank you

Link to comment
Share on other sites

  • Corsair Employees

Lets try replacing your modules.

Please send us a email with a copy of the form or all of your info name address and phone# and the Module part# and copy the link to this post and email it to Warranty@corsairmemory.com. Or you can also use the On Line RMA Request Form as well.

If after 1 day or 24 hours excluding weekends you do not get the rma please email the same to rma@corsairmemory.com and we will help to resolve it.

Link to comment
Share on other sites


This topic is now archived and is closed to further replies.

  • Create New...