The Corsair User Forums  

Go Back   The Corsair User Forums > Corsair Product Discussion > Cooling

Reply
 
Thread Tools Search this Thread Rate Thread Display Modes
  #1  
Old 08-14-2016, 01:44 AM
sk2536 sk2536 is offline
Registered User
sk2536's PC Specs
 
Join Date: Aug 2016
Posts: 2
POST ID # = 867126
sk2536 Reputation: 10
Default corsair h115i with noctua nf-a14 industrial 3000

Hello,

1) Can i use noctua nf-a14 industrialppc-3000 pwm fans with h115i .

2) Since fans are connected to pump ,will pump supply enough power to these fans . The fans are rated at 6.66 watt each .

3) Do i have to connect sata power cable to psu?

Thanks and regards.
Reply With Quote


  #2  
Old 08-14-2016, 04:28 AM
red-ray red-ray is offline
Banned
red-ray's PC Specs
 
Join Date: May 2014
Location: England (GMT+1)
Posts: 7,152
POST ID # = 867136
red-ray Reputation: 81
Thumbs up Yes, Yes and Yes

  1. Yes
  2. They are connected to the H115i controller which can supply a total of 2 amps (24 watts) so yes. The pump is also connected to the H115i controller.
  3. Yes
Reply With Quote


  #3  
Old 08-14-2016, 04:41 AM
sk2536 sk2536 is offline
Registered User
sk2536's PC Specs
 
Join Date: Aug 2016
Posts: 2
POST ID # = 867138
sk2536 Reputation: 10
Default

Ok Thanks lot for reply.
Reply With Quote


  #4  
Old 08-14-2016, 07:48 AM
c-attack c-attack is offline
Registered User
c-attack's PC Specs
 
Join Date: Jun 2014
Posts: 10,083
POST ID # = 867147
c-attack c-attack Reputation: 107
Default

Yes, you can run them. However, you are unlikely to recognize a cooling difference in that upper range. The amount of airflow through the radiator is not normally the limiting factor. I don't see meaningful cooling differences above 1600 with the identical blade 2000 rpm model in a larger watt system. Also, the 3000 rpm model will have an 800-850 minimum speed, compared to 400-500 on the 2000 rpm model. If they are for special circumstances only, that is one thing, but it's a lot of fan for everyday use.

Last edited by c-attack; 08-14-2016 at 01:59 PM.
Reply With Quote


  #5  
Old 08-14-2016, 01:12 PM
magma82 magma82 is offline
Registered User
 
Join Date: Jun 2016
Posts: 22
POST ID # = 867171
magma82 Reputation: 10
Default

not go for 3000 take 2000, you take only extra loud, no better performance :D
Reply With Quote


  #6  
Old 08-15-2016, 05:14 PM
Tallfeather Tallfeather is offline
Registered User
Tallfeather's PC Specs
 
Join Date: Jul 2016
Posts: 7
POST ID # = 867383
Tallfeather Reputation: 10
Default

As others say, you really don't need high RPMs. The benefit of a huge radiator is that it actually requires very little airflow to work very well.

I run my noctua A14 fans at 1k, and it's silent while my CPU never goes above 60C. That is with full burn-test loads. With normal usage, looking at my max temp in the monitor for this session (several days of running) - it's 51C. Water temps do not exceed 40C.

No need to run a turbine in your system, let the big radiators radiate. :)
Reply With Quote


  #7  
Old 09-11-2016, 08:52 AM
stilup stilup is offline
stilup
stilup's PC Specs
 
Join Date: Feb 2006
Location: East Hartford CT USA
Posts: 8
POST ID # = 870897
stilup Reputation: 10
Default

I agree , I also run the 2000 version and runs just less than 1000 rpm , silent and stays cool.
Reply With Quote


  #8  
Old 09-12-2016, 05:24 PM
AAOO AAOO is offline
Registered User
 
Join Date: Sep 2016
Posts: 5
POST ID # = 871098
AAOO Reputation: 10
Default

I have 4X Noctua NF A14 industrialPPC-2000 in a Push/Pull configuration and couldn't be happier, minus the price...

Much quieter than the stock blenders that were emitting some sort of audible frequency that was driving me crazy.

Some say Push/Pull won't make much a diff on water temps with this rad which is probably true, but it helped drop my case temps 5c which helps my GPU run cooler. Mine is setup as intake.

Go with the 2000's for the lower idle speeds. They are silent under 900 RPM and I haven't seen them go much higher than 900 RPM doing everyday tasks with everything set to quiet.
Reply With Quote


  #9  
Old 09-13-2016, 07:12 PM
Everborn128 Everborn128 is offline
Registered User
Everborn128's PC Specs
 
Join Date: Jan 2014
Posts: 49
POST ID # = 871213
Everborn128 Reputation: 10
Default

I have a h100i v2 & I replaced the stock jet engine fans with Noctua NF-F12 fans, they are 1500rpm max opposed to the 2500rpm max stock fans. I'm very very happy with the upgrade, the temps only dropped 2c but the upgrade was mainly for the noise reduction. I never considered the stock fans over 1150rpm fans because they were so loud above that rpm.

I now run my noctuas at 1200ish rpm & let them kick up to 1500(max) if I get above 70c which is very rare, however they are almost dead silent at max as well. I wouldn't recommend going higher RPM fans the temp difference, if any.. isn't worth the noise. Even noctua will be loud at that RPM.
Reply With Quote


Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:00 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.