EnglishBloke Posted October 12, 2020 Share Posted October 12, 2020 (edited) TLDR; Three QL120's connected to Lighting Node CORE then to Commander Pro, not showing up in iCUE PRODUCTS -Corsair Carbide Spec-06 White Case -iCUE LS100 Starter Kit -H100i AIO Cooler -QL120 RGB Fan Kit (Contains Lighting Node) -Commander Pro -RGB Hub SETUP Firstly I have fitted the LS100 kit inside my case, with two of the 250mm strips internally and one of the 450mm strips replacing the LED's that came in the front of the case as they were not iCUE compatible. These are daisy chained and connected to LED Port 2 in the Commander Pro. I took the two LL120 fans from the H100i and mounted them inside my case. These both go to the RGB Hub which is then connected to LED port 2 of the Commander Pro. For my H100i I have mounted 2 QL120 fans to it (Because the LL120's face the wrong way so the lights would be pointing at the radiator and the front of my case is covered). The third QL120 is below the radiator. All three of these fans go to the included Lightning Node CORE, which is connected to the Commander Pro via USB port 1. All accessories are lit using a Lighting Link mode. PROBLEM The QL120's cannot be found in the iCUE software. When connected to the Lighting Node they simply light up white. There is no option for selecting the Lightning Node in the software, even through the Commander Pro. If I connect one to the RGB Hub and tell it I have 3 fans then the connected QL will display the test LED, but because the RGB Hub is set up for the LL120's, I cannot connect all the QL's through the Hub as they have more LED's and they will not light up correctly. EXTRA While extremely unlikely to be related, I recently replaced my PSU and Motherboard. I'm 75% certain that the RGB in the QL120's were editable through iCUE before this. I did not unplug anything relating to them except the fan control to the AIO pump, which is now connected again. Edited October 12, 2020 by EnglishBloke Link to comment Share on other sites More sharing options...
c-attack Posted October 12, 2020 Share Posted October 12, 2020 Since the QLs are connected to a Lighting Node Core, you are looking for that device at the top of the CUE window. If it does not show, you most likely have a USB recognition problem. 1) Check the USB 2 plug on the Commander passthrough. The receptacle is large and it is very easy to misalign the USB plug on the pins. 2) Try it at another USB port, on the Commander, your USB hub, or MB directly. The x570 motherboard seem to be finicky about USB connections. You also can try other device USB plugs on the Commander to see if anything is recognized. Link to comment Share on other sites More sharing options...
jfevey92 Posted January 20, 2021 Share Posted January 20, 2021 I am having the same issue and I also have the asus prime x570 pro. Did you ever find a fix? Link to comment Share on other sites More sharing options...
Big_Boss Posted January 20, 2021 Share Posted January 20, 2021 I am also having a similar problem, my lighting node pro is dectected in usbdeview but is not dectected at all by icue so I am stuck on rainbow on my lighting strips and rgb fans. What i found very odd is that when i uninstall icue and install Link, everything works fine but i cant change the rgb of my vengance ram as it is icue only! Link to comment Share on other sites More sharing options...
teezee1000 Posted January 23, 2021 Share Posted January 23, 2021 I am also having a similar problem, my lighting node pro is dectected in usbdeview but is not dectected at all by icue so I am stuck on rainbow on my lighting strips and rgb fans. What i found very odd is that when i uninstall icue and install Link, everything works fine but i cant change the rgb of my vengance ram as it is icue only! I have this same exact issue as well, I can see the node in ILINK but not in ICUE (which I used to be able to see, I believe one of the many updates stopped it) Link to comment Share on other sites More sharing options...
Recommended Posts