KBhamm Posted September 11, 2019 Share Posted September 11, 2019 The led Profile wont move, and it doesnt accept changes in Fan RPM. Logs in attachment. Only a Hard reboot will help. So i need to get the pc completly of. then it works for a few seconds or minutes. i can change the leds of the whole pc. only the pump gets stuck.asd.zip Link to comment Share on other sites More sharing options...
xMacias Posted September 11, 2019 Share Posted September 11, 2019 Is this new after installing 3.19? Link to comment Share on other sites More sharing options...
KBhamm Posted September 11, 2019 Author Share Posted September 11, 2019 Yes I just uninstalling icue and it doesn't come back, with installing a older version of icue it is now the same only without icue it runs fine but before 3.19 it never happened, the temp sensors get stuck, the rgb effect doesn't move anymore and it doesn't accept rpm changes. Is there any way to get a image of an older firmware? Link to comment Share on other sites More sharing options...
c-attack Posted September 11, 2019 Share Posted September 11, 2019 I can send this on to the iCUE team, but since you have RGB RAM you don't want to be on 3.19 right now anyway. Roll back to 3.18. Link to comment Share on other sites More sharing options...
KBhamm Posted September 11, 2019 Author Share Posted September 11, 2019 Why? I have software control inside the ram offline so no 10% usage on cpu :D but now I get it that's the problem users complain about at the moment... Im currently without icue because with icue my aio just doesn't work. 3 hours playing now not a single stuck of the aio... Now I install icue 3.18 or 3.19 the stuck starts again Link to comment Share on other sites More sharing options...
c-attack Posted September 11, 2019 Share Posted September 11, 2019 The 3.19 and RGB RAM issues are not directly related to iCUE software control "check box". I only use hardware mode, I do not have any odd CPU usage percentages, but am still very much affected by system interrupts crippling CPU metrics and performance. I am not sure I understand the "Now I install icue 3.18 or 3.19 the stuck starts again". Are you saying the cooler is locking up on 3.18 as well? Link to comment Share on other sites More sharing options...
KBhamm Posted September 11, 2019 Author Share Posted September 11, 2019 Yes it belongs to the sentence in front of the 3 dots sorry English isn't my native one :P I played few hours with icue. Then I installed 3.18 it locked up same as 3.19. I did a complete reinstall again now it works fine for more than 10 minutes with 3.18.77 maybe something screwed up some registry files before maybe it works now :) Link to comment Share on other sites More sharing options...
c-attack Posted September 11, 2019 Share Posted September 11, 2019 ... now it works fine for more than 10 minutes with 3.18.77 maybe something screwed up some registry files before maybe it works now :) Install corruption seems to be one of the more common issues. If you are on 3.18.77 and things seem to be OK, leave it alone. There is nothing in 3.19 that should be critical to your use and hopefully we will see another version shortly. Link to comment Share on other sites More sharing options...
KBhamm Posted September 11, 2019 Author Share Posted September 11, 2019 Yeah but please still send this to the beta team. An malfunctioning aio can cause serious hardware damage. I just tried it again it happens with 3.19. Link to comment Share on other sites More sharing options...
DevBiker Posted September 11, 2019 Share Posted September 11, 2019 Are you running any other monitoring tools? And ... while a malfunctioning cooler can damage hardware, you'll see CPU temps spike. If you've not seen it, the cooler is still operating even if the monitoring isn't. Even still, modern CPUs will throttle as well. So ... permanent damage is unlikely. Link to comment Share on other sites More sharing options...
KBhamm Posted September 12, 2019 Author Share Posted September 12, 2019 (edited) I don't use any monitoring tool since February the aio gets constantly disconnected after starting any monitoring tool... The same for the commander pro. Nop the temperature rises because of not increasing the rpm. But this is different than the usb reconnect error. The pump just get stuck spinning at the rpm it has while getting stuck. No change even if the fluid temp rises and rises (got an IR temp sensor right on the radiator and it reaches 50 degrees celsius while the fans spin very low) Edited September 12, 2019 by KBhamm Link to comment Share on other sites More sharing options...
KBhamm Posted October 6, 2019 Author Share Posted October 6, 2019 The pump still has this issue, it's since the pump firmware update 1.15.... Link to comment Share on other sites More sharing options...
Recommended Posts