The Corsair User Forums  

Go Back   The Corsair User Forums > Search Forums

Notices

Showing results 1 to 25 of 8778
Search took 0.28 seconds.
Search: Posts Made By: DevBiker
Forum: iCUE Software 07-01-2020, 09:56 PM
Replies: 3
Views: 40
Posted By DevBiker
The fans can be put on a PWM splitter. No more...

The fans can be put on a PWM splitter. No more than 2 to a header and no more than 9 to a CoPro.

For the strips, you'll need a Lighting Node Pro. No way around that.
Forum: iCUE Software 07-01-2020, 05:37 PM
Replies: 6
Views: 143
Posted By DevBiker
The SLC has 3 wires - voltage, data, and ground....

The SLC has 3 wires - voltage, data, and ground. That's it. Only 1 data line (and yes, ground is required).
Forum: iCUE Software 07-01-2020, 05:34 PM
Replies: 6
Views: 143
Posted By DevBiker
Not sure. What I don't know is if there are fuses...

Not sure. What I don't know is if there are fuses in there to prevent you from drawing too much current.


The digital control signal isn't something that you measure in mA. There is very little...
Forum: Cases 07-01-2020, 01:00 AM
Replies: 1
Views: 75
Posted By DevBiker
First, you cannot put the ML-RGB fans on the same...

First, you cannot put the ML-RGB fans on the same hub as the SP-RGB fans. Different protocol.

Next, if the fans are still controlled by the case buttons then you still have it connected to the...
Forum: Ambient Lighting 07-01-2020, 12:05 AM
Replies: 4
Views: 128
Posted By DevBiker
Very cool stuff there!

Very cool stuff there!
Forum: System Builds, Modding, Custom Components, and Picture Gallery 07-01-2020, 12:00 AM
Replies: 2
Views: 77
Posted By DevBiker
I don't see anything wrong. Very nice cable...

I don't see anything wrong. Very nice cable routing, by the way!!
Forum: Cooling 06-30-2020, 09:13 PM
Replies: 2
Views: 76
Posted By DevBiker
You can only control fan speeds in iCUE using a...

You can only control fan speeds in iCUE using a Commander Pro. If they aren't connected to a CoPro, then you'll need to control them with whatever device they are connected to (like the AIO or the...
Forum: Cooling 06-30-2020, 09:11 PM
Replies: 7
Views: 192
Posted By DevBiker
Yes, the power cable is fine. The 1000D has...

Yes, the power cable is fine.

The 1000D has a pass-through at the end of the front panel LEDs that you can connect the fan hub to.
And just one LNP will do for the fans. But ... you might want...
Forum: Cooling 06-30-2020, 09:09 PM
Replies: 1
Views: 59
Posted By DevBiker
Yes, you can connect the fans to the motherboard....

Yes, you can connect the fans to the motherboard. It's not ideal but it'll work.

And no, you should not use HWInfo to read the pump's readings. It will interfere with iCUE and cause all kinds of...
Forum: Ambient Lighting 06-30-2020, 09:06 PM
Replies: 1
Views: 85
Posted By DevBiker
The connectors are different, yes. No, they won't...

The connectors are different, yes. No, they won't work with the LS100.
Forum: Cooling 06-30-2020, 11:44 AM
Replies: 7
Views: 192
Posted By DevBiker
The signature is at the bottom of my post....

The signature is at the bottom of my post. There's a section for "Helpful Links and FAQs".
And yes, 3 hubs would do the trick. You'd also need 3 channels. So ... the CoPro + a NoPro.

If you got...
Forum: iCUE Software 06-30-2020, 11:42 AM
Replies: 1
Views: 97
Posted By DevBiker
First, the Core doesn't "see" or "detect" the...

First, the Core doesn't "see" or "detect" the fans connected - you have to tell it what's there. So it'll treat your fans however you tell it to.
Now, there isn't official support for multiple fan...
Forum: Cooling 06-30-2020, 09:58 AM
Replies: 7
Views: 192
Posted By DevBiker
You'll need 2-3 Fan Hubs. The limit of 6 is...

You'll need 2-3 Fan Hubs.
The limit of 6 is due to power draw limits. You do not want to put 13 LL fans on a single SATA power connector!
See the RGB FAQ linked in my signature.
Forum: iCUE Software 06-30-2020, 01:03 AM
Replies: 6
Views: 143
Posted By DevBiker
LEDs vary on the draw but most are less that .3W....

LEDs vary on the draw but most are less that .3W. 60 LEDs typically comes in around 2.1-2.2A.
I did measurements of the Corsair RGB, including the LS100 strips -...
Forum: iCUE Software 06-29-2020, 06:39 PM
Replies: 1
Views: 95
Posted By DevBiker
The Lighting Node Pro has two channels - as long...

The Lighting Node Pro has two channels - as long as you have the fans connected to fan hubs on different channels, it'll work just fine.

Check out the RGB FAQ in my sig ...
Forum: Cooling 06-29-2020, 01:03 PM
Replies: 4
Views: 149
Posted By DevBiker
Ryzen Master won't be an issue. We've seen issues...

Ryzen Master won't be an issue. We've seen issues particularly with HWInfo.

And ... yeah, if it's only happening in one game than I'd suspect something with the game. What game would that be?
Forum: Hydro X Custom Cooling 06-29-2020, 12:59 PM
Replies: 2
Views: 69
Posted By DevBiker
The fan speed for the fans connected to the H100i...

The fan speed for the fans connected to the H100i V2 isn't reported to the motherboard at all. It will report about 1/2 of the pump speed - to prevent CPU_FAN warning.

And make sure that the fan...
Forum: iCUE Profiles 06-29-2020, 02:05 AM
Replies: 2
Views: 110
Posted By DevBiker
There are 3rd party RGB Fan Splitters available...

There are 3rd party RGB Fan Splitters available that will do the trick. You'll have 2 QLs that are identical but they will all light up.

To control the QL fans from the Commander Pro, you'll need...
Forum: System Builds, Modding, Custom Components, and Picture Gallery 06-29-2020, 01:48 AM
Replies: 6
Views: 121
Posted By DevBiker
^^ Definitely. Even if you have a hand drawn...

^^ Definitely.
Even if you have a hand drawn mess that you scan and upload, we won't judge and guide you where you need to be. ;)
Forum: Cooling 06-29-2020, 01:29 AM
Replies: 4
Views: 149
Posted By DevBiker
Are you running any other monitoring software?

Are you running any other monitoring software?
Forum: Cooling 06-29-2020, 01:00 AM
Replies: 5
Views: 164
Posted By DevBiker
Oh, it's possible. But the effects on the strips...

Oh, it's possible. But the effects on the strips will be wonky - they'd have to be treated "like fans".
Forum: System Builds, Modding, Custom Components, and Picture Gallery 06-29-2020, 12:40 AM
Replies: 6
Views: 121
Posted By DevBiker
Zotty used MSPaint.

Zotty used MSPaint.
Forum: Cooling 06-24-2020, 06:49 PM
Replies: 2
Views: 129
Posted By DevBiker
First, how is the channel configured? You have to...

First, how is the channel configured? You have to tell iCUE how many and what kind of fan is on the channel.
Second, are they in the hub in ports 1,2,3,4? No skipping! And when you said you tried...
Forum: Cooling 06-24-2020, 12:48 AM
Replies: 7
Views: 269
Posted By DevBiker
With a CoPro, the Fan Hub that came with your...

With a CoPro, the Fan Hub that came with your case would connect to it. The Lighting Node Core that came with the SP-PRO could use the USB port but it is its own RGB controller. And the CoPro will be...
Forum: iCUE Software 06-24-2020, 12:38 AM
Replies: 2
Views: 144
Posted By DevBiker
Yes, you can save the H100iV2 to memory. You...

Yes, you can save the H100iV2 to memory. You should have a "SD-Card" type icon in the Hamburger menu on the Performance Tab. This should save the curve to the device. (Sorry - that's from memory -...
Showing results 1 to 25 of 8778

 
Forum Jump

All times are GMT -4. The time now is 04:39 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.