The Corsair User Forums  

Go Back   The Corsair User Forums > Search Forums

Showing results 1 to 25 of 149
Search took 0 seconds.
Search: Posts Made By: A Computer Guy
Forum: Memory 09-08-2019, 12:35 PM
Replies: 11
Views: 924
Posted By A Computer Guy
If your new to memory overclocking with Ryzen CPU...

If your new to memory overclocking with Ryzen CPU read this first.
https://www.techpowerup.com/review/amd-ryzen-memory-tweaking-overclocking-guide/

Ensure your ram is installed in your primary...
Forum: Memory 09-07-2019, 08:53 PM
Replies: 11
Views: 924
Posted By A Computer Guy
My screenshot showed a successful DDR4-3600...

My screenshot showed a successful DDR4-3600 overclock and DDR4-3200 with tightened timings with my dual-rank kit. It was successful until I updated my BIOS to AGESA 1.0.0.3ABB and I am back to...
Forum: Memory 09-07-2019, 08:28 PM
Replies: 11
Views: 924
Posted By A Computer Guy
Typically first I use the bootable memtest86 USB...

Typically first I use the bootable memtest86 USB and don't event bother booting into windows unless at least one pass is successful.

Secondly that is why I tend to use a scratch disk OS for...
Forum: Memory 09-05-2019, 09:18 PM
Replies: 11
Views: 924
Posted By A Computer Guy
I also have a kit of 4.32 ram (different model,...

I also have a kit of 4.32 ram (different model, size, and dual rank) and found it didn't like tRC timings (and some lower tRFC) out of the box and were a bit problematic to get working. I needed to...
Forum: Memory 09-02-2019, 01:20 PM
Replies: 8
Views: 774
Posted By A Computer Guy
When you get your system put together you will...

When you get your system put together you will need to get familiar with your BIOS/UEFI. This is where you will need to configure your memory. If your using compatible memory then it may be as...
Forum: Memory 09-02-2019, 12:29 PM
Replies: 9
Views: 4,856
Posted By A Computer Guy
Have you tried adjusting your SOC voltage while 2...

Have you tried adjusting your SOC voltage while 2 sticks are installed before installing all 4?

Quotes from link below:
"Generally, the best SOC values fall between 0.97–1.025 V."
"A change...
Forum: Memory 09-01-2019, 02:14 AM
Replies: 8
Views: 774
Posted By A Computer Guy
The answer to the first part is *maybe*. Only...

The answer to the first part is *maybe*. Only getting a kit of 4 will reduce the likelihood of issues being caused by otherwise mixing two kits when you intend to fill all 4 slots.



The safest...
Forum: Memory 08-31-2019, 07:02 PM
Replies: 9
Views: 4,856
Posted By A Computer Guy
Sorry it's unclear...have you tried any other...

Sorry it's unclear...have you tried any other combinations of ProcODT and RTT values besides what was suggested by dram calculator?

I think it would be helpful if another user with a Zen2 CPU on...
Forum: Memory 08-30-2019, 05:26 PM
Replies: 8
Views: 774
Posted By A Computer Guy
Please don't both post here and pm me at the same...

Please don't both post here and pm me at the same time. One copy of the same message is enough, preferably keep it in the forum. Thanks.

Typically not recommended to mix any two kits together...
Forum: Memory 08-29-2019, 11:55 PM
Replies: 8
Views: 774
Posted By A Computer Guy
No definite answer to your question but consider...

No definite answer to your question but consider this...

Instead of CMW32GX4M2C3200C16 consider CMW32GX4M2Z3200C16 instead since it is expressly advertised as AMD compatible memory where the other...
Forum: Memory 08-28-2019, 11:52 PM
Replies: 3
Views: 266
Posted By A Computer Guy
The DRAM voltage should be printed on the back of...

The DRAM voltage should be printed on the back of your memory module next to the model and version number. Typically 1.35v is common but you need to check to be sure.
Forum: Memory 08-28-2019, 12:04 AM
Replies: 3
Views: 266
Posted By A Computer Guy
XMP doesn't always work. Make sure your ram is...

XMP doesn't always work. Make sure your ram is installed in slots A2 and B2.

Basically try using AUTO memory settings then manually enter your DRAM voltage, frequency, and timings. Run memtest86...
Forum: Memory 08-27-2019, 08:34 PM
Replies: 3
Views: 319
Posted By A Computer Guy
This looks like a 8GB stick from a 16GB set. So...

This looks like a 8GB stick from a 16GB set. So basically your running two different vendor sticks of 8GB memory for a total of 16GB.
Forum: Solid State Drives (SSD) 08-22-2019, 11:18 PM
Replies: 60
Views: 95,181
Posted By A Computer Guy
Not quite what I was getting at. For example if...

Not quite what I was getting at. For example if you already had DDR4-3200 (which runs at a lower IF already) and decoupled the IF up to 1800MHz while maintaining the same memory clock.

I...
Forum: Memory 08-22-2019, 10:37 PM
Replies: 2
Views: 494
Posted By A Computer Guy
I'm not sure I can really recommend a memory kit...

I'm not sure I can really recommend a memory kit however here is what I would consider in your case and a few of my opinions.

The following article will help you understand various aspects of ram...
Forum: Solid State Drives (SSD) 08-21-2019, 08:40 PM
Replies: 60
Views: 95,181
Posted By A Computer Guy
I have a bit of a tangential question for those...

I have a bit of a tangential question for those with these large MP600's, I hope you don't mind since you have one of these large performance NVMe drives and your waiting for Corsair to hopefully...
Forum: Memory 08-21-2019, 08:16 PM
Replies: 1
Views: 696
Posted By A Computer Guy
Question: What is the version number of your ram...

Question: What is the version number of your ram kit?

Try this simplified procedure...

1) Make sure your ram is installed in the primary channel on slots A2 & B2 and that you have the desired...
Forum: Memory 08-21-2019, 02:37 AM
Replies: 9
Views: 4,856
Posted By A Computer Guy
I wonder if you may need to reconfigure your...

I wonder if you may need to reconfigure your ProcODT and RTT values in BIOS/UEFI to find a compatible set of options that will allow you to post with both 2 or 4 sticks. This way perhaps you can...
Forum: Memory 08-19-2019, 10:48 PM
Replies: 1
Views: 2,579
Posted By A Computer Guy
JEDEC speeds are supposed to work out of the box....

JEDEC speeds are supposed to work out of the box. Unfortunately XMP doesn't always work out of the box and the solution is typically to manually enter voltage, frequency, and timings.

Try this...
Forum: Solid State Drives (SSD) 08-19-2019, 08:55 PM
Replies: 60
Views: 95,181
Posted By A Computer Guy
Do you have any options in your BIOS/UEFI to set...

Do you have any options in your BIOS/UEFI to set M.2 PCIe as Gen3 vs. Gen4 and possibly 2x vs 4x mode?
Forum: Cases 08-18-2019, 07:45 PM
Replies: 8
Views: 1,268
Posted By A Computer Guy
In the front can't you mount the fans in front of...

In the front can't you mount the fans in front of the rad (push) instead of behind it (pull)?
Forum: Memory 08-18-2019, 07:42 PM
Replies: 9
Views: 4,856
Posted By A Computer Guy
It seems lately there have been quite a few...

It seems lately there have been quite a few Gigabyte X570 users having problems recently.

Will it not post with all 4 or is it just having a massive amount of errors during memtest86?
Forum: Solid State Drives (SSD) 08-18-2019, 07:18 PM
Replies: 60
Views: 95,181
Posted By A Computer Guy
Do you have icue or steam running? Try closing...

Do you have icue or steam running? Try closing those and pause any running anti-virus. They may impact user benchmark scores.
Forum: iCUE Software 08-18-2019, 10:09 AM
Replies: 8
Views: 899
Posted By A Computer Guy
iCue is not going to damage your CPU.

iCue is not going to damage your CPU.
Forum: Solid State Drives (SSD) 08-14-2019, 09:10 PM
Replies: 60
Views: 95,181
Posted By A Computer Guy
I see a new firmware (F3i) for your board...

I see a new firmware (F3i) for your board released recently.
Did you try that yet?
Showing results 1 to 25 of 149

 
Forum Jump

All times are GMT -4. The time now is 03:24 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.