The Corsair User Forums  

Go Back   The Corsair User Forums > Search Forums

Notices

Showing results 1 to 25 of 8790
Search took 0.30 seconds.
Search: Posts Made By: DevBiker
Forum: Cooling 07-07-2020, 10:30 AM
Replies: 3
Views: 87
Posted By DevBiker
You can use 2-way splitters - there's enough...

You can use 2-way splitters - there's enough current available for that.
Forum: Cooling 07-06-2020, 06:28 PM
Replies: 1
Views: 49
Posted By DevBiker
Yes, a PWM splitter will be fine. Just make...

Yes, a PWM splitter will be fine.
Just make sure that the header and the splitter are both 4-pin PWM and that the header is set to PWM mode. That will ensure that you have a constant 12V.
Forum: Cooling 07-06-2020, 04:15 PM
Replies: 1
Views: 49
Posted By DevBiker
Not needed, no. If you want to control the fan...

Not needed, no. If you want to control the fan speeds in iCUE, however, that's what you'll have to do.


Correct.


They can probably go on a USB 3.0 header if you have one of those USB 3.0...
Forum: Hydro X Custom Cooling 07-06-2020, 12:36 PM
Replies: 9
Views: 117
Posted By DevBiker
The readings are still available on the...

The readings are still available on the Dashboard. There's no "unlocking" them.
Forum: iCUE Software 07-06-2020, 12:35 PM
Replies: 4
Views: 106
Posted By DevBiker
Well ... I certainly have it available. Where are...

Well ... I certainly have it available. Where are you looking for it?
Forum: Keyboards and Mice 07-06-2020, 12:32 PM
Replies: 2
Views: 54
Posted By DevBiker
https://www.corsair.com/us/en/Categories/Products/...

https://www.corsair.com/us/en/Categories/Products/Accessories-%7C-Parts/pbt-config/p/CH-9000235-WW
You can get black or white.
Or both and mix 'em up.
Forum: Cooling 07-06-2020, 11:43 AM
Replies: 3
Views: 87
Posted By DevBiker
The fans should be connected to the pump - that's...

The fans should be connected to the pump - that's the ideal location for them as it'll be able to control them based on pump temp even when iCUE isn't running.

Typically, the fans on the cooler...
Forum: Hydro X Custom Cooling 07-06-2020, 11:40 AM
Replies: 2
Views: 66
Posted By DevBiker
What port is your HydroX temp sensor in? It...

What port is your HydroX temp sensor in?
It looks like you have two of them.
That message isn't telling you that it doesn't see the sensors - it's stating that the curve is based on the temp...
Forum: Corsair Link 07-04-2020, 11:45 PM
Replies: 77
Views: 54,653
Posted By DevBiker
Both are possible. PirateDog Tech has them...

Both are possible.
PirateDog Tech has them available but here are your pinouts:
Pin 1 is marked on the connector with a triangle/arrow.
Fan:
1: +5V
2: Data Out (from Fan)
3: Data In (to...
Forum: Cooling 07-04-2020, 11:38 PM
Replies: 6
Views: 158
Posted By DevBiker
Here's the pinout, starting with Pin 1 (with the...

Here's the pinout, starting with Pin 1 (with the arrow on the connector).
1: +5V
2: Data Out (From Fan)
3: Data In (To Fan)
4: Ground

The minimum that you need to get it to light up is +5V,...
Forum: iCUE Software 07-02-2020, 06:08 PM
Replies: 2
Views: 119
Posted By DevBiker
Let's make sure that we're clear here - RGB...

Let's make sure that we're clear here - RGB Control for the keyboard (and other HID devices ... "outside the box") will still work.
Any internal devices (coolers, fans, etc) won't work without the...
Forum: Cooling 07-02-2020, 06:06 PM
Replies: 4
Views: 96
Posted By DevBiker
Yes, you can enable Q-Fan control when you switch.

Yes, you can enable Q-Fan control when you switch.
Forum: iCUE Software 07-01-2020, 09:56 PM
Replies: 3
Views: 97
Posted By DevBiker
The fans can be put on a PWM splitter. No more...

The fans can be put on a PWM splitter. No more than 2 to a header and no more than 9 to a CoPro.

For the strips, you'll need a Lighting Node Pro. No way around that.
Forum: iCUE Software 07-01-2020, 05:37 PM
Replies: 8
Views: 265
Posted By DevBiker
The SLC has 3 wires - voltage, data, and ground....

The SLC has 3 wires - voltage, data, and ground. That's it. Only 1 data line (and yes, ground is required).
Forum: iCUE Software 07-01-2020, 05:34 PM
Replies: 8
Views: 265
Posted By DevBiker
Not sure. What I don't know is if there are fuses...

Not sure. What I don't know is if there are fuses in there to prevent you from drawing too much current.


The digital control signal isn't something that you measure in mA. There is very little...
Forum: Cases 07-01-2020, 01:00 AM
Replies: 1
Views: 128
Posted By DevBiker
First, you cannot put the ML-RGB fans on the same...

First, you cannot put the ML-RGB fans on the same hub as the SP-RGB fans. Different protocol.

Next, if the fans are still controlled by the case buttons then you still have it connected to the...
Forum: Ambient Lighting 07-01-2020, 12:05 AM
Replies: 5
Views: 209
Posted By DevBiker
Very cool stuff there!

Very cool stuff there!
Forum: System Builds, Modding, Custom Components, and Picture Gallery 07-01-2020, 12:00 AM
Replies: 2
Views: 115
Posted By DevBiker
I don't see anything wrong. Very nice cable...

I don't see anything wrong. Very nice cable routing, by the way!!
Forum: Cooling 06-30-2020, 09:13 PM
Replies: 2
Views: 128
Posted By DevBiker
You can only control fan speeds in iCUE using a...

You can only control fan speeds in iCUE using a Commander Pro. If they aren't connected to a CoPro, then you'll need to control them with whatever device they are connected to (like the AIO or the...
Forum: Cooling 06-30-2020, 09:11 PM
Replies: 7
Views: 247
Posted By DevBiker
Yes, the power cable is fine. The 1000D has...

Yes, the power cable is fine.

The 1000D has a pass-through at the end of the front panel LEDs that you can connect the fan hub to.
And just one LNP will do for the fans. But ... you might want...
Forum: Cooling 06-30-2020, 09:09 PM
Replies: 1
Views: 96
Posted By DevBiker
Yes, you can connect the fans to the motherboard....

Yes, you can connect the fans to the motherboard. It's not ideal but it'll work.

And no, you should not use HWInfo to read the pump's readings. It will interfere with iCUE and cause all kinds of...
Forum: Ambient Lighting 06-30-2020, 09:06 PM
Replies: 1
Views: 122
Posted By DevBiker
The connectors are different, yes. No, they won't...

The connectors are different, yes. No, they won't work with the LS100.
Forum: Cooling 06-30-2020, 11:44 AM
Replies: 7
Views: 247
Posted By DevBiker
The signature is at the bottom of my post....

The signature is at the bottom of my post. There's a section for "Helpful Links and FAQs".
And yes, 3 hubs would do the trick. You'd also need 3 channels. So ... the CoPro + a NoPro.

If you got...
Forum: iCUE Software 06-30-2020, 11:42 AM
Replies: 1
Views: 123
Posted By DevBiker
First, the Core doesn't "see" or "detect" the...

First, the Core doesn't "see" or "detect" the fans connected - you have to tell it what's there. So it'll treat your fans however you tell it to.
Now, there isn't official support for multiple fan...
Forum: Cooling 06-30-2020, 09:58 AM
Replies: 7
Views: 247
Posted By DevBiker
You'll need 2-3 Fan Hubs. The limit of 6 is...

You'll need 2-3 Fan Hubs.
The limit of 6 is due to power draw limits. You do not want to put 13 LL fans on a single SATA power connector!
See the RGB FAQ linked in my signature.
Showing results 1 to 25 of 8790

 
Forum Jump

All times are GMT -4. The time now is 10:55 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.