The Corsair User Forums  

Go Back   The Corsair User Forums > Search Forums

Notices

Showing results 1 to 12 of 12
Search took 0 seconds.
Search: Posts Made By: iced98lx
Forum: Cooling 10-08-2005, 12:10 AM
Replies: 26
Views: 3,890
Posted By iced98lx
great info for a7n8-e board owners.. You didn't...

great info for a7n8-e board owners.. You didn't put the sensor between the core and the copper did you? more generally just to the side of core..

your shims, this seems interesting, are they...
Forum: Cooling 10-05-2005, 10:21 AM
Replies: 26
Views: 3,890
Posted By iced98lx
well that's a pretty good load figure as far as I...

well that's a pretty good load figure as far as I can see... The SHIM i'm refering to is just peice of copper or non-cunductive material (cardboard) you can order online.. just make sure you get one...
Forum: Cooling 10-04-2005, 10:07 PM
Replies: 26
Views: 3,890
Posted By iced98lx
mines gotten better with a Shim, if you don't...

mines gotten better with a Shim, if you don't have one, get one. Evidentally the block doesn't sit level with out it.. I'm idling right now at 44 that's without the fan on the rad on.. (hehe, I like...
Forum: Cooling 09-28-2005, 12:02 PM
Replies: 26
Views: 3,890
Posted By iced98lx
okay I just inverted my rad completely, no air...

okay I just inverted my rad completely, no air came out. (I was dissapointed)

here's a question- when you hook your tach signal wire up to your MB header, what RPM does it tell you? My pump is...
Forum: Cooling 09-28-2005, 11:34 AM
Replies: 26
Views: 3,890
Posted By iced98lx
Air In RAD

well that makes sense, my rad was filled while it was mounted, barbs down.

*smacks head* duh. I'll have to take it off and spin it around... (good thing I left some excess tubing!) see if any...
Forum: Cooling 09-27-2005, 09:32 PM
Replies: 26
Views: 3,890
Posted By iced98lx
Angry Exactly- I moved my PC into the house after...

Exactly- I moved my PC into the house after working on it in the garage and BAM idle temps are back to 46-48 instead of 44. I'm going to get a shim and maybe a small coldplate and see if that helps.....
Forum: Cooling 09-24-2005, 04:13 PM
Replies: 26
Views: 3,890
Posted By iced98lx
Fixer

well I had a revelation.. I reseated it, and suddenly.. it worked.

not spectacularly, but decent.

I idle at 44 and load to 53~ish. (48 if the room is cool, 65-70, 53 is room temp at 80) My...
Forum: Cooling 09-22-2005, 06:46 PM
Replies: 26
Views: 3,890
Posted By iced98lx
room temps are 70-72 degrees F.

room temps are 70-72 degrees F.
Forum: Cooling 09-22-2005, 01:59 PM
Replies: 26
Views: 3,890
Posted By iced98lx
I'll slide my mobotray out and see if I can get...

I'll slide my mobotray out and see if I can get any paper etc between.. just check the gap.. otherwise I"m out of options!

chris
Forum: Cooling 09-22-2005, 11:12 AM
Replies: 26
Views: 3,890
Posted By iced98lx
my concerns exactly, but the compound seems to...

my concerns exactly, but the compound seems to leave a nice uniform rectangle.. (not that this couldn't occur when I was holding it up to seat it)

I'm thinking a very thin copper cold plate might...
Forum: Cooling 09-22-2005, 09:21 AM
Replies: 26
Views: 3,890
Posted By iced98lx
flow is great, I can monitor the system in the...

flow is great, I can monitor the system in the bios until it gets to 50 degrees or so, shut it down, pull off the block and hte copper is cool to the touch, where as anything else on the board is...
Forum: Cooling 09-21-2005, 11:05 PM
Replies: 26
Views: 3,890
Posted By iced98lx
Angry Athlon XP3200 Corsair 1001

I've installed the Corsair 1001 system on my XP3200 and I"m haveing drat for luck on temps. Currently the system will only idle at 47-50.. which is rather dissapointing. Also, when did the fans...
Showing results 1 to 12 of 12

 
Forum Jump

All times are GMT -4. The time now is 11:52 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.