The Corsair User Forums  

Go Back   The Corsair User Forums > Search Forums

Notices

Showing results 1 to 13 of 13
Search took 0 seconds.
Search: Posts Made By: lhyde
Forum: Cooling 10-08-2005, 12:48 AM
Replies: 26
Views: 3,890
Posted By lhyde
My shim is a ThermalTake 1215. No cross braces,...

My shim is a ThermalTake 1215. No cross braces, but fairly wide around the edges. It doesn't touch on any part of the chip or the visible components on the CPU board.
The sensor is between the...
Forum: Cooling 10-07-2005, 07:38 PM
Replies: 26
Views: 3,890
Posted By lhyde
I removed the shim and reseated the waterblock...

I removed the shim and reseated the waterblock with a Antec P160 sensor under the ridged area of the waterblock. Using ASUS probe the CPU temp is 46*C at idle and 52*C under load (Prime95 & SETI),...
Forum: Cooling 10-07-2005, 06:32 PM
Replies: 26
Views: 3,890
Posted By lhyde
Well I added the shim to the Barton that runs...

Well I added the shim to the Barton that runs hotter. Temps actually got hotter (55*C) under load. and are about 46* at idle. Using ASUS probe and MBM 5, temps read the same, but that is expected,...
Forum: Cooling 10-05-2005, 11:50 AM
Replies: 26
Views: 3,890
Posted By lhyde
I found an outlet for ThermalTake AMD shims....

I found an outlet for ThermalTake AMD shims. ($4.00 CDN) I ordered 2.
I'm not OC'g the Bartons; but I have 2 P4's that are OC'd at 15 percent. I run SETI@Home CLI on all PC's 24/7/365. CPU...
Forum: Cooling 10-04-2005, 10:27 PM
Replies: 26
Views: 3,890
Posted By lhyde
I reseated the block today. (A7N8X-E-Dx) Not much...

I reseated the block today. (A7N8X-E-Dx) Not much difference ... now running at 47*C under load. So what do I need to order? A shim for Socket A or Athlon XP? The other Barton 2800 is still at...
Forum: Cooling 10-01-2005, 11:09 PM
Replies: 26
Views: 3,890
Posted By lhyde
I've been away for a few days. My CPU temp...

I've been away for a few days. My CPU temp dropped from 51*C to 48*C. Not as much as I had hoped. My pumps (all 4) all run about 3540rpm. They vary a little as the power supply 12v fluctuates; but...
Forum: Cooling 09-28-2005, 02:59 AM
Replies: 26
Views: 3,890
Posted By lhyde
Surprise... Surprise. There was more air in the...

Surprise... Surprise. There was more air in the system. The rad was half full. Originally, when filling the system, I would lay the rad flat on the table barbs up; pump the fluid thru and then...
Forum: Cooling 09-27-2005, 07:18 PM
Replies: 26
Views: 3,890
Posted By lhyde
Thanks CaptC: I'll check that out again. I did...

Thanks CaptC: I'll check that out again. I did burp it pretty well and did the 45* tilt thing again, but I did notice it didn't take as much fluid as the other installs. I did check for kinks and...
Forum: Cooling 09-27-2005, 06:22 PM
Replies: 26
Views: 3,890
Posted By lhyde
I completed the conversion on the last PC. ...

I completed the conversion on the last PC. A7N8X-DX/Barton 2800. Before conversion to Corsair Cool: CPU temp 50*C; MB 33*C; room 23*C. After Conversion: CPU 40*C; MB 30*C; room 23*C.
This seems...
Forum: Cooling 09-24-2005, 02:07 AM
Replies: 26
Views: 3,890
Posted By lhyde
Well, I've just spent the better part of a day...

Well, I've just spent the better part of a day transfering my A7N8X-E-Dx/Barton 2800 from a 24" tower that had poor airflow; to my new Antec P160. While doing this conversion, I added a CWC100-1001....
Forum: Cooling 09-22-2005, 11:47 AM
Replies: 26
Views: 3,890
Posted By lhyde
I think when I do my conversion; I will add the...

I think when I do my conversion; I will add the CPU block with the mobo out of the case. This way I can maybe see gaps, or maybe use a feeler gauge to see if there is space between CPU and Block.
Forum: Cooling 09-22-2005, 10:59 AM
Replies: 26
Views: 3,890
Posted By lhyde
My kits arrived to water cool the AMD Barton...

My kits arrived to water cool the AMD Barton 2800's. Also a P160. I'll let you know in a day or 2 if my conversion went ok. Gonna move one system from a 24" tower to the P160. Then in a week...
Forum: Cooling 09-22-2005, 01:07 AM
Replies: 26
Views: 3,890
Posted By lhyde
Check the tubing for kinks or narrowed sections. ...

Check the tubing for kinks or narrowed sections. Any restrictions to fluid flow?
Showing results 1 to 13 of 13

 
Forum Jump

All times are GMT -4. The time now is 10:42 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.