The Corsair User Forums  

Go Back   The Corsair User Forums > Search Forums

Notices

Showing results 1 to 25 of 47
Search took 0 seconds.
Search: Posts Made By: jase439
Forum: Audio 02-10-2020, 08:31 PM
Replies: 22
Views: 8,892
Posted By jase439
Installed the newest iCUE, 3.25.60 today (clean...

Installed the newest iCUE, 3.25.60 today (clean install, removed all devices from device manager, etc). MIC/Audio crackling is gone (knock on wood). Curious if anyone else experienced similar.
Forum: Audio 01-27-2020, 04:57 PM
Replies: 22
Views: 8,892
Posted By jase439
Honestly, given all the recent reports of audio...

Honestly, given all the recent reports of audio corruption in this forum, I am surprised that Corsair has not responded given what clearly seems to be an obvious software/driver issue in Windows 10....
Forum: Audio 01-24-2020, 09:15 PM
Replies: 22
Views: 8,892
Posted By jase439
I'm started having this issue also. I "suspect"...

I'm started having this issue also. I "suspect" the issue is related to changes to audio introduced by a recent Windows 10 update. I've isolated my problem to the mic being active. If the application...
Forum: Memory 01-12-2012, 07:08 PM
Replies: 4
Views: 4,658
Posted By jase439
I tried raising both the controller and DRAM...

I tried raising both the controller and DRAM voltage - thinking maybe I was in violation of the sacrosanct 0.5v rule - without success. Unfortunately, the BIOS on this system doesn't give the kind of...
Forum: Memory 01-12-2012, 05:42 PM
Replies: 4
Views: 4,658
Posted By jase439
I think I'll recant just a bit. There doesn't...

I think I'll recant just a bit. There doesn't really seem to be any real correlation between stability and voltage in this configuration. I think I just had a "lucky" run. Back to running crappy...
Forum: Memory 01-12-2012, 01:48 AM
Replies: 4
Views: 4,658
Posted By jase439
CMT16GX3M4X2133C9 + Alienware Aurora-R3 - Unhappy Marriage

I recently purchased 4 sticks of CMT16GX3M4X2133C9 Corsair memory to replace the 8GB of lower-quality Micron memory in my new Alienware Aurora-R3. The system is running an Intel i7-2600k processor @...
Forum: Memory 08-03-2010, 03:03 AM
Replies: 9
Views: 5,327
Posted By jase439
Stock voltage for 2 sticks is 1.5V. Your mobo...

Stock voltage for 2 sticks is 1.5V. Your mobo may be undervolting. You may need to bump it to 1.6.

Timing should be 9-9-9-24.
Forum: Memory 08-03-2010, 02:39 AM
Replies: 13
Views: 6,161
Posted By jase439
I was advised today that the DHX series is...

I was advised today that the DHX series is discontinued and that the comparable replacement part is CMP4GX3M2C1600C7. However, I was reading that this DDR3 module was designed for the Intel Core...
Forum: Memory 07-29-2010, 04:36 PM
Replies: 5
Views: 3,813
Posted By jase439
Are you running with 4-sticks? It can take some...

Are you running with 4-sticks? It can take some real teeth-pulling to get 4-sticks running stable at 1600. Even with 2-sticks, I don't think there are many BIOSes which will run 1600Mhz with stock...
Forum: Memory 07-28-2010, 10:27 PM
Replies: 13
Views: 6,161
Posted By jase439
I guess I'll change out all 4. I'd rather not...

I guess I'll change out all 4. I'd rather not have to deal with the headache caused by timing issues related to version mismatch (been down that road already once).
Forum: Memory 07-27-2010, 11:36 PM
Replies: 13
Views: 6,161
Posted By jase439
Thank you for getting back to me. Should I...

Thank you for getting back to me.

Should I RMA all four sticks? Three of them appear to be just fine. Can I RMA just the defective stick and get a replacement that exactly matches the other 3? ...
Forum: Memory 07-26-2010, 11:01 PM
Replies: 13
Views: 6,161
Posted By jase439
At the moment, it isn't even handling 2 (I've...

At the moment, it isn't even handling 2 (I've backed away from 4 sticks at the moment to give the memory controller as much benefit of the doubt). But I think I have a bead on one particular stick...
Forum: Memory 07-26-2010, 06:15 PM
Replies: 13
Views: 6,161
Posted By jase439
They are. I ordered 2 pairs of...

They are. I ordered 2 pairs of CM3X1024-1600C7DHX. I've had them for a couple years though. Here's the specs from the back of the modules (they are all identical):

XMS3-1600 1024MB 1600Mhz...
Forum: Memory 07-26-2010, 04:38 PM
Replies: 13
Views: 6,161
Posted By jase439
NB hangs out around 42-43 at idle, and tops out...

NB hangs out around 42-43 at idle, and tops out around 48-49 under load. I think I've seen it as high as 51 once. How hot is too hot in your experience?

Will try disabling USB legacy and see...
Forum: Memory 07-26-2010, 03:40 PM
Replies: 13
Views: 6,161
Posted By jase439
Why would two sticks of RAM at DDR-1600 report a...

Why would two sticks of RAM at DDR-1600 report a bandwidth of 6015MB/s in memtest, but two different but identical sticks (make/model/version) of RAM at the same timings and same slots report only...
Forum: Memory 07-26-2010, 01:11 AM
Replies: 13
Views: 6,161
Posted By jase439
Puzzling Memtest 86+ Test#7 Errors with 4x1GB Dual-Channel X38 MB

Hi all. I could use some collective wisdom from the forum regarding a puzzling phenomenon I have been unable to resolve (or understand).

I have 4 sticks of 1600C7DHX in my Asus Maximus Extreme...
Forum: Overclocking and Benchmarking 05-27-2008, 08:33 PM
Replies: 1
Views: 1,450
Posted By jase439
Squirrely Temps and 45nm Quads

What's the scoop with temperature sensors on these Q96xx/X33xx CPU's? I have some tools telling my core temps are idling in the high 50's. I have others (real temp) telling me I'm idling in the low...
Forum: Memory 05-24-2008, 01:36 AM
Replies: 28
Views: 7,297
Posted By jase439
It turned out to be nothing more than Windoze...

It turned out to be nothing more than Windoze taking it upon myself to configure my IDE controller for PIO mode. Aside from being horrifically slow, apparently bad things happen when you move files...
Forum: Memory 05-22-2008, 11:06 PM
Replies: 28
Views: 7,297
Posted By jase439
My apologies in advance for committing thread...

My apologies in advance for committing thread necromancy (and being somewhat off topic at this point). I was just curious if anyone has experienced ICHR9R southbridge instability with mild-moderate...
Forum: Memory 05-16-2008, 12:33 AM
Replies: 28
Views: 7,297
Posted By jase439
I was able to get 4 sticks running at DDR-1500...

I was able to get 4 sticks running at DDR-1500 (375FSB). I wasn't *quite* able to get 7-6-6 to take at that speed. I was getting 1 or 2 errors every couple of passes through memtest and I couldn't...
Forum: Memory 05-15-2008, 09:32 PM
Replies: 28
Views: 7,297
Posted By jase439
Clock skew is an amazingly wonderous thing. Last...

Clock skew is an amazingly wonderous thing. Last night, I was able to get two sticks stable at 7-6-6-18 w/ FSB@375 (DDR-1500). I dropped the other two in and immediately the universe fell apart...
Forum: Memory 05-13-2008, 10:36 PM
Replies: 28
Views: 7,297
Posted By jase439
I've started to keep an Excel table of...

I've started to keep an Excel table of incremental tweaks w/ remarks on stability and performance. I'm finding a few trends:

DRAM Static Read is more or less lethal to any overclocking effort;...
Forum: Memory 05-13-2008, 09:29 PM
Replies: 28
Views: 7,297
Posted By jase439
Presently, I am testing with just 2 sticks total...

Presently, I am testing with just 2 sticks total as it appears all bets are off with 4. But so far I have been unsuccessful in getting even 2 sticks to run at DDR1600 on this board. I was going to...
Forum: Memory 05-13-2008, 09:42 AM
Replies: 28
Views: 7,297
Posted By jase439
If anyone following this thread happens to have...

If anyone following this thread happens to have the Maximus paired with TWO sticks of TWIN3X2048-1600C7DHX and has successfully achieved FSB400/DDR1600, I would be interested to know what BIOS...
Forum: Memory 05-13-2008, 01:08 AM
Replies: 28
Views: 7,297
Posted By jase439
It appears the instability is curable with a bump...

It appears the instability is curable with a bump on the NB voltage and FSB Strap @ 333. I can't seem to get 2 sticks to pass memtest at DDR1600 just yet - even with the voltage bump - but I can...
Showing results 1 to 25 of 47

 
Forum Jump

All times are GMT -4. The time now is 09:10 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2020, vBulletin Solutions, Inc.