The Corsair User Forums  

Go Back   The Corsair User Forums > Search Forums

Showing results 1 to 25 of 8984
Search took 0.45 seconds.
Search: Posts Made By: c-attack
Forum: Gaming Enthusiasts Area 09-15-2019, 05:36 PM
Replies: 3
Views: 106
Posted By c-attack
The H100i Pro is showing because you have...

The H100i Pro is showing because you have connected the USB 2 from it to the motherboard. That is the more critical element to ensure you have control. The 2 pin plug coming off the pump is a...
Forum: iCUE Profiles 09-15-2019, 05:23 PM
Replies: 2
Views: 34
Posted By c-attack
You need to create the profile in one of the...

You need to create the profile in one of the three hardware profiles. Those will have a different icon and be labeled something like "Strafe RGB MK.2 HW1-3". That is a special profile slot not...
Forum: Cases 09-15-2019, 11:57 AM
Replies: 1
Views: 33
Posted By c-attack
Unfortunately this is a common obstacle and the...

Unfortunately this is a common obstacle and the case frame has never been great for 360mm radiators. However, the part I really don’t understand is the very short center mounting rail in top of the...
Forum: Cooling 09-15-2019, 11:29 AM
Replies: 17
Views: 155
Posted By c-attack
Your PSU would slam off to protect itself or you...

Your PSU would slam off to protect itself or you would see/smell smoke. You are probably just under the 12v limit for the SATA line, but being "just under" is not necessarily safe when it comes to...
Forum: Cooling 09-15-2019, 11:02 AM
Replies: 17
Views: 155
Posted By c-attack
No 3 way fan splitters for LL/HD fans. Too close...

No 3 way fan splitters for LL/HD fans. Too close to the limit. 2 way splitters only, and one is all you need for 7 fan motors.

If you are now down to 7 RGB fans (not 10), you may be able to...
Forum: Cooling 09-15-2019, 09:24 AM
Replies: 17
Views: 155
Posted By c-attack
I would not go for push-pull on the 360mm AIO. ...

I would not go for push-pull on the 360mm AIO. This is likely counter-productive to your goals. On a 360mm radiator, push push has a very nominal effect at 300W+. At the 75-135W your CPU outputs,...
Forum: Cooling 09-15-2019, 08:33 AM
Replies: 17
Views: 155
Posted By c-attack
1) While I would not characterize the LL as great...

1) While I would not characterize the LL as great airflow fans on or off a radiator, that's not really the point. The difference between a "great radiator fan" and an average one is going to be...
Forum: iCUE Software 09-14-2019, 07:38 PM
Replies: 6
Views: 99
Posted By c-attack
Correct. If you feel you the need, you can set...

Correct. If you feel you the need, you can set the games up in the NVCP for "maximum performance" on the power behavior leaving the default to Optimal. I think that would be mopre effective than...
Forum: Cooling 09-14-2019, 06:43 PM
Replies: 4
Views: 148
Posted By c-attack
Sorry, missed this originally. I would...

Sorry, missed this originally. I would definitely put one at the rear exhaust. That is going to be the primary heat exit point and these probes become valuable as a control source for the case...
Forum: iCUE Software 09-14-2019, 06:02 PM
Replies: 6
Views: 99
Posted By c-attack
The game is minimized to the task bar and iCUE is...

The game is minimized to the task bar and iCUE is up and in focus. That's why I was wondering about NVCP power settings for your GPU or perhaps the 980 Ti can't do chill out like the newer cards. ...
Forum: Cooling 09-14-2019, 05:54 PM
Replies: 3
Views: 48
Posted By c-attack
That is in the expected range although you really...

That is in the expected range although you really need to the room and case temp to put it in perspective. Regardless, if the idle coolant temp value is 31-ish and your CPU temps are 40-something,...
Forum: iCUE Software 09-14-2019, 05:14 PM
Replies: 3
Views: 607
Posted By c-attack
You don't want your screen running in GSync...

You don't want your screen running in GSync windowed mode or it will do this with any application that uses GPU resources. "Full Screen Only" is the best set up for most people, but if you actually...
Forum: iCUE Software 09-14-2019, 05:11 PM
Replies: 1
Views: 37
Posted By c-attack
Presumably you have a Corsair mouse or this won't...

Presumably you have a Corsair mouse or this won't be an iCUE setting. Based on the model, you may be able to save your own DPI settings to the hardware that will be in place until the software...
Forum: iCUE Software 09-14-2019, 11:23 AM
Replies: 6
Views: 99
Posted By c-attack
Assuming your "M65" is a M65 RGB or M65 Pro, you...

Assuming your "M65" is a M65 RGB or M65 Pro, you have hardware save slots for saving basic lighting profiles. Obviously one of the choices is 0,0,0 off.

iCUE has both graphing and animations in...
Forum: Cooling 09-14-2019, 11:18 AM
Replies: 11
Views: 135
Posted By c-attack
The "on the table shot" is almost 1:1 on my...

The "on the table shot" is almost 1:1 on my monitor and I am holding a long ~30mm 6-32 next to it. It looks really close to being right. However, when I scan your short screws, it looks like there...
Forum: Keyboards and Mice 09-14-2019, 08:04 AM
Replies: 14
Views: 1,021
Posted By c-attack
Get someone to help you do the hard reset. That...

Get someone to help you do the hard reset. That is the firmware fix. If that does not do it, then I am not sure what else can be done. This is not a software issue. It is either hardware or...
Forum: Cooling 09-14-2019, 07:57 AM
Replies: 17
Views: 155
Posted By c-attack
On a technical level, a RGB fan is going to have...

On a technical level, a RGB fan is going to have a higher level of "noise" than an identical non-RGB fan. The power used to create the lighting is not free or perfect in terms of energy conversion. ...
Forum: Cooling 09-14-2019, 07:49 AM
Replies: 11
Views: 135
Posted By c-attack
I am open to second opinions, but those all look...

I am open to second opinions, but those all look like #8 screws to me. A standard short stubby fan screw that comes in with your average fan is #8 and those are also used for some custom cooling...
Forum: Cooling 09-13-2019, 06:55 PM
Replies: 17
Views: 155
Posted By c-attack
ML fans are also going to have some measure of...

ML fans are also going to have some measure of bearing noise because of the unique design. While they offer less noise at moderate speed, I would not suggest it for a zero noise case. It is higher...
Forum: Cooling 09-13-2019, 06:47 PM
Replies: 11
Views: 135
Posted By c-attack
I think the relevant shot would be of the...

I think the relevant shot would be of the radiator screw hole itself and whether one of the short screws will thread at all. It's hard for us to see or do much on this end, but this is the first...
Forum: Cooling 09-13-2019, 05:00 PM
Replies: 17
Views: 155
Posted By c-attack
My preference would be to avoid the lowest pump...

My preference would be to avoid the lowest pump speed altogether. If you were transitioning from the desktop to a load situation (like gaming or whatever), you would need to run the fans and pump...
Forum: Cooling 09-13-2019, 04:54 PM
Replies: 11
Views: 135
Posted By c-attack
Uh no. Stop. Screws do not go through the...

Uh no. Stop. Screws do not go through the radiator. If you are mounting fans to it, you use the longer 27-30mm 6-32 machine screws. If you are mounting the radiator to case, you only need the...
Forum: Cooling 09-13-2019, 04:25 PM
Replies: 3
Views: 48
Posted By c-attack
You need to look at coolant temperature (H110i...

You need to look at coolant temperature (H110i Temp) to assess cooler function. Most people will idle 4-7C above the room temp or equal to the case ambient temperature. Load temps might eventually...
Forum: Cooling 09-13-2019, 09:19 AM
Replies: 17
Views: 155
Posted By c-attack
Most H150i and H115i Pro users report zero to...

Most H150i and H115i Pro users report zero to little difference between the Balanced 2160 and Extreme 2850 rpm speeds. High flow rate does not usually offer the same benefits as higher fan speed.
...
Forum: iCUE Software 09-13-2019, 06:08 AM
Replies: 23
Views: 970
Posted By c-attack
I am not sure what issues you are referencing....

I am not sure what issues you are referencing. Everyone, including me, that was affected by the system interrupt issue has resolved the issue by going back to 3.18.77. Perhaps it would be advisable...
Showing results 1 to 25 of 8984

 
Forum Jump

All times are GMT -4. The time now is 10:50 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.