The Corsair User Forums  

Go Back   The Corsair User Forums > Search Forums

Showing results 1 to 18 of 18
Search took 0.02 seconds.
Search: Posts Made By: E-ric
Forum: Audio 02-02-2019, 09:38 PM
Replies: 1
Views: 424
Posted By E-ric
Void Pro Surround and Focusright 6i6

Can these headphones in any way connect to an external amp like the Focusrite Scarlett 6i6 and still be able to use the mic on the headphones?
...
Forum: Memory 06-11-2013, 03:19 PM
Replies: 2
Views: 2,046
Posted By E-ric
Thanks, appreciate it!

Thanks, appreciate it!
Forum: Memory 06-10-2013, 09:38 PM
Replies: 2
Views: 2,046
Posted By E-ric
CMD32GX3M4A2133C9 32gb overclocking help

I have a rampage IV extreme, with 3930k and just finished a water cooling loop. I brought my cpu up to 4.4 and was curious to know about my memory settings. I set the freq to 2133 and matched the...
Forum: Power Supplies 06-07-2013, 12:05 PM
Replies: 4
Views: 1,667
Posted By E-ric
This is the pump ...

This is the pump

http://www.frozencpu.com/products/17549/ex-pmp-214/Swiftech_MCP655-PWM-DRIVE_12v_Water_Pump_Module_-_PWM_Enabled_Single_Version.html?id=99XZ2mh8&mv_pc=145

So i should be fine...
Forum: Power Supplies 06-06-2013, 08:56 PM
Replies: 4
Views: 1,667
Posted By E-ric
ax1200I question

I have two mpc655 pumps, pwm version connected to one strip going into the psu..is this save or do I need to divide them between cables?
Forum: Memory 05-30-2013, 10:02 PM
Replies: 5
Views: 3,322
Posted By E-ric
I decided to just leave them alone and not use...

I decided to just leave them alone and not use the blocks.
Forum: Memory 05-26-2013, 03:18 AM
Replies: 5
Views: 3,322
Posted By E-ric
yup.. is a heat gun all I need?

yup.. is a heat gun all I need?
Forum: Memory 05-25-2013, 06:25 PM
Replies: 5
Views: 3,322
Posted By E-ric
heat spreader removal

Can I remove the heat spreaders off my corsair dominator platinum with just a heat gun?
Forum: Cooling 12-10-2011, 03:15 PM
Replies: 21
Views: 11,879
Posted By E-ric
I have 11359403, just installed after RMAing my...

I have 11359403, just installed after RMAing my other which the pump died along with the lights..this has me worrying now..ugh. Hopefully mine will last longer than 6 months..
Forum: Cooling 12-08-2011, 10:45 PM
Replies: 5
Views: 7,541
Posted By E-ric
thanks, not at all..with performance mode on the...

thanks, not at all..with performance mode on the h100..barely here it at all;)
Forum: Cooling 12-08-2011, 10:17 PM
Replies: 5
Views: 7,541
Posted By E-ric
H100 4 fan setup a bad idea?

Wondering if setting up 2 fans on the bottom and two on the top of the radiator for a push pull outside the top of my haf 932 is a good idea, im kinda thinking i might be limiting air flow some how...
Forum: Cooling 11-23-2011, 07:47 PM
Replies: 1
Views: 1,894
Posted By E-ric
H100 making buzzing noise and lights flickering

Started hearing a buzzing noise or like a hard drive write noise and investigated only to see the lights on the front of the H100 were out (lights that show fan speed) and the pump is reporting in...
Forum: Cooling 10-16-2011, 12:54 AM
Replies: 7
Views: 4,361
Posted By E-ric
I have 4 cougar vortex fans set up in a push pull...

I have 4 cougar vortex fans set up in a push pull throwing air outside the case, do you think this is hindering air flow in any way?
Forum: Cooling 10-16-2011, 12:49 AM
Replies: 7
Views: 4,361
Posted By E-ric
Thank you for the reply~! Got it.

Thank you for the reply~! Got it.
Forum: Cooling 10-15-2011, 10:23 PM
Replies: 17
Views: 6,988
Posted By E-ric
do you have any settings in the bios...

do you have any settings in the bios automatically setting your fan speeds? if so change em to manual and 100%
Forum: Cooling 10-15-2011, 10:00 PM
Replies: 7
Views: 4,361
Posted By E-ric
thanks, my HW monitor shows 2040 for the cpu fan...

thanks, my HW monitor shows 2040 for the cpu fan speed. The screws look the same as the ones corsair provided but silver and with the philips at the top to tighten down. Ill replace them with ones...
Forum: Cooling 10-15-2011, 09:34 PM
Replies: 7
Views: 4,361
Posted By E-ric
Is my H100 working right?

Installed this today after lapping my 920, at first start up i head the water going through the tubes and it seemed to be working great, I didnt realize that the thumb screws provided were the only...
Forum: Memory 11-15-2009, 05:29 PM
Replies: 3
Views: 3,649
Posted By E-ric
Asus Maximus Extreme with CM3X1024-1800C7D bios settings

I currently have 2GB of this memory installed and i was in the process of learning up on overclocking my processor and memory. Right now my timings on this are 7-7-7-20, and DRAM Freq set to...
Showing results 1 to 18 of 18

 
Forum Jump

All times are GMT -4. The time now is 07:47 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.