Jump to content

Padinn

Members
  • Posts

    32
  • Joined

Reputation

10 Good
  1. I don't see that version of the firmware for the K95 RGB Platinum XT - sure you got the right model there?
  2. Quick question, I'm guessing with repeater I'll lose ability to monitor fan RPM. Is that right? Or does it send one rpm signal!
  3. Appreciate your advice, I grabbed the corsair one. I originally though I'd need to spend like 70 for the Commander Pro - but this is perfect and very reasonable after I looked at cost of some others. Thanks for your guidance.
  4. Oh looking at this, that Carbide Repeater might be just what I need....wish shipping wasn't double cost of item though :D
  5. Well, I see that point, but I really just need to know how much current the pump draws (maybe MCU too - not sure what that is) None of the fans I am using have RGB. Only RGB is on pump. I'd rather not spend the $70 or so if I don't have too, I probably would just find a cheap 6 fan controller and use that in a PWM spot on the motherboard.
  6. Just a quick bump, FAQ says .45a so I think I am good.
  7. To give you a sense of this, a few months back my cpu was crashing on a normally stable overclock. Turned out one of the icue updates had reser my profile and pump was on quiet. Turning it to extreme dropped coolant temperatures by almost 5c instantly. With the heat the 9900k produces, the low flow rate of quiet pump operation means liquid sits there longer than im.comfortsble with. You could try a custom pump profile too.
  8. With the 9900k increase pump speed. I have same cpu and cooler and on silent temps are much higher. It doesn't push liquid fast enough on low settings. I personally cant hear pump on extreme, so I leave it there.
  9. Make sure you've got your pump set to "Extreme" and double check your fans speeds. I only hit 91c on full load stress test. Your liquid temperatures seem pretty high - I keep my home around 78-80F and my radiator temperatures maxed around 40c when running fans in extreme mode. Using my push pull, they max around 36.5c under full load, and around 33c gaming/streaming. This is on an H150i, but I don't think its much better than a 115i pro.
  10. Hello, I would like to setup my H150i using push pull. I will be using 3 stock fans and 3 Corsair CO-9050014-WW fans (these are rated at .25a each). I know the stock fans are rated at .219a. I can't figure out if the pump is able to power these by itself without damaging it, I know it has a 2.0a limit, but am confused on if pump needs .45a or .6a. Based on my calculations, if the pump is .45a, I'm fine (~1.86a total), but if its .6, I'm a bit over (2.007a, which leaves no wiggle room). I assume this would only happen at max power draw but want to be safe. Can anyone share their thoughts?
  11. I figured it out! This is by far the weirdest bug I've ever encountered. I had set the numpad key to be my record last five minutes option in Nvidia Geforce Shadowplay. For whatever reason this prevents windows from detecting the key input. I verified that by switching the bind to another key the issue returns. You can hold escape to delete the bind and everything works fine then.
  12. Hey folks, I have a K70 Vengeance. I recently ran into an error that is driving me nuts, but I can't figure out the cause. My asterisk key on numpad will no longer input in windows, but I have verified with Switch Hitter that the computer is detecting the input properly. All the other numpad keys work fine. Any idea what is going on? I am on Windows 10
  13. Regular K70. I notice my headset doesn't save settings either, so I think it's related to my new motherboards USB settings.
  14. Since upgrading my motherboard I've noticed my k70 will not save settings after power down. For example the windows key lock resets. How can I fix this?
×
×
  • Create New...