CamStrifeFFVII

will do, if i run into any issue, I'll be sure to post here for help. Thanks again Zotty :biggrin:

wow, an epic light show/impressive build layout right there:): those images gives me some ideas for my loops thanks for posting them :winking: well done on getting the dual build fully completed :sunglasse

sorry for the late message back Zotty, been super busy with work. (build up to Christmas starts around end of October - Early November with my job) Thanks for sharing the video.:D: I'll get myself some mounting brackets for my reservoirs like shown in this video that should help me better plan out the loop as well. Fingers crossed we see RNDA2 with Big Navi early next year. anyway once I've got everything sorted and purchased remaining parts, I'll get around to posting the end results. Might be a couple to a few months depending on GPU release date. You've been an awesome help Zotty.:praise:

Thanks for the advice Zotty, I'll make it separate loops to make things a little easier. appreciate the suggestions :) I'll get another pump and reservoir, I'll use one of the front 480 rads on for the ITX build. i'll use the other 480 and 420 rads for the 3950X build. As for the the radiators, I used the EKWB custom loop configurator to help with the rad compatibility for the Corsair Obsidian 1000D case. When I got them in the mail, I made sure to fit them, in which they did and with plenty of clearance as well :) I'll start thinking about locations to put in the second pump combo so i can plan in another drain fitting. Thanks again for the help :) CamStrifeFFVII

Good Evening Zotty, I'm new to the Corsair Forums and have been reading your thread over the past few months for inspiration on my own Corsair Obsidian 1000D Build. (really great build by the way) :D: I'm planning out a Dual Build System and have been struggling to plan out how to setup my system to have two builds in one custom loop (all watercooling parts are EK and Loop fans (Corsair) will utilise Commander Pro's and Light Node Pro's currently planning to use 25 fans in push/pull configuration). I'm trying to plan the loop to allow both system in the case to power on the loop (not sure if it's possible). I haven't been able to figure out how to go about it. if possible could you help me out by making a diagram for this configuration. I will be using a drain location directly after the pump (res is separated by fitting and tubing then connects to pump) after that will be rotary - x splitter - (attached to front of x Splitter, Back of x Splitter will be closed off with a Plug) rotary and (finally) Ball Baring drain fitting. The reservoir will be placed in the area where mounting area is to the front of case (if that makes sense) pump underneath it. my Builds will mainly be used for Gaming (4K HDR 60fps minimum), 3D Rendering, 3D Modelling, teaching myself how to code in Unreal 4 and Unity Engine, Texturing and playing around with game engines. 1st Build (ITX): (playing around with Game Engines, Texturing) AMD R9 3900X G.Skill Flare X 16GB 3200mhz CL14 RAM Gigabyte X570-I Aorus Pro Corsair SF750W Platinum PSU Samsung 512GB Pro NVMe M.2 SSD (boot drive) Samsung 3TB (SATA II) HDD (from old Build) Seagate Barracuda 2TB HDD (from old build) Intel 300 Series 120GB SSD Sandisk 480GB Extreme SSD Gigabyte 1080Ti Waterforce Extreme (AIO) Windows 10 Pro 2nd Build: (Rendering, 3D modelling, Gaming) AMD R9 3950X (when available) - need to purchase G.Skill Trident Z Royal (Gold) either (4x8GB Quad channel CL14 3200mhz or 2x16GB Dual Channel CL14 3200mhz) - need to purchase Asus X470 ROG Crosshair Hero VII (WIFI) Corsair AX1200i (considering this to be a test PSU for dead components/building other peoples PC. may consider getting Corsair AX1000 Titanium) Samsung 2TB M.2 NVMe (PCIe) EVO Plus SSD (boot drive) - need to purchase (2x maybe) AMD High-End Navi (when available and will be adding to loop) - need to purchase Windows 10 Pro - need to purchase Watercoooling Parts: EK PE 480 rads (2) EK CE 420 rad (1) EK ACF fittings - Copper (16) EK Res X3 250 RGB EK Pump (sleeved) EK Velocity (AMD) Copper Plexi (for 3900X) EK Monoblock (AMD) (for Crosshair VII Hero) EK X Splitter EK Male to Male rotary fitting (2) EK Ball Baring Drain fitting EK QDC fittings 10mm - Black (7) Other Components: PrimoChill Primoflex AdvancedLRT clear tubing 10ft (10mmID,16mmOD) Corsair LL120 - white (19) (3 x three pack with Light Node Pro) Corsair LL140 - Black (6) (3 x dual pack with Light Node Pro) Corsair Commander Pro (2) (not including inbuilt Obsidian 1000D Commander Pro) - need to purchase would i be better off going two separate loops if its not possible for the both systems on one loop? Any advice or suggestions would be greatly appreciated :D: Kind Regards, CamStrifeFFVII