Weird problems with Fan RPMs and H100 Pump RPM

[vullprofiman]

Since the update to the Corsair Link Software 1.2.7. Beta

If have got really weird problems with the RPMs of my fans of my H100 and the H100 Pump..
I have 4 Fans plugged into my H100
2 Cougar 120mm PWM
and 2 E.N.E.R.M.A.X. Trio 120mm PWM

The Cougar Fans 800 to 1500 RPMs
and the E.N.E.R.M.A.X. 600-1800 RPMs

After the Update the Link Software Reports me RPMs up to 2200 for the Cougar and 2100 for the E.N.E.R.M.A.X.
and the RPMs of the H100 Pump are even higher than normal
Normaly it is always about 2200rpms but now I have about 2400-2600 RPM.....

I am really worried could it be that my H100 is defect or is it the software?

[randolla]

Originally Posted by vullprofiman

Since the update to the Corsair Link Software 1.2.7. Beta

If have got really weird problems with the RPMs of my fans of my H100 and the H100 Pump..
I have 4 Fans plugged into my H100
2 Cougar 120mm PWM
and 2 E.N.E.R.M.A.X. Trio 120mm PWM

The Cougar Fans 800 to 1500 RPMs
and the E.N.E.R.M.A.X. 600-1800 RPMs

After the Update the Link Software Reports me RPMs up to 2200 for the Cougar and 2100 for the E.N.E.R.M.A.X.
and the RPMs of the H100 Pump are even higher than normal
Normaly it is always about 2200rpms but now I have about 2400-2600 RPM.....

I am really worried could it be that my H100 is defect or is it the software?

My guess it is the software. There is a multiplyer for the pump that may have been reset that now needs to be changed back. I would not worry too much about the fan's RPMs. They are most likely just being reported a bit differently.

Good luck

[RAM GUY]

Did you update the Cooling Node Firmware as well?
And please check the Pump RPM (CPU_FAN) in your BIOS hardware manager.

[vullprofiman]

THX Ram Guy for answering

Yes I did update the Firmware of the Cooling Node
But I only have the RPM Problems with the fans pluggend into my H100

I am using CPUID Hardware Monitor for checking the RPMs of the pump on my mainboard the max RPM it reads is about 2600
I will check out in the BIOS the RPMs too and then post it

I have also noticed that if I chose the Low Noise Profile all 4 H100-Fans are about 200-400 RPMs faster than the settings in the Profile

If I want the fans to run at the RPMs I want I have to set them to the Fixed RPM Mode

Also each time I start up I have to reload my profile because after the restart of my PC the fixed RPM of the H100 Fans is this ridiculos high MaxRPM

[Arimis5226]

This is similar to a problem I started having. It wasn't like this before, it just sorta popped up a week or two ago. I, however, did not update any firmware. It was working fine for months, and then I started seeing really high RPM reporting on my fans but the fans weren't really going that fast.

[RAM GUY]

I have also noticed that if I chose the Low Noise Profile all 4 H100-Fans are about 200-400 RPMs faster than the settings in the Profile

Can you be more specific and provide a screen shot please?

If I want the fans to run at the RPMs I want I have to set them to the Fixed RPM Mode

A: This can only be done in the Corsair Link software.

Also each time I start up I have to reload my profile because after the restart of my PC the fixed RPM of the H100 Fans is this ridiculos high Max RPM

A: Yes that is a known issue and will be addressed in a future release.

[vullprofiman]

When the Fans of my H100 are set to the Low Noise Profile the RPMs should be about 1100 RPMs maximum but they are much higher
H100 Fan 1 and 2 are the Cougar Fans and 3 and 4 are the E.N.E.R.M.A.X.
The shown RPMs of the H100 Fans are in realitiy much lower than displayed
because if you look at the second picture, the temp of the coolant is much lower with the fans set to a really low fixed RPM
Also on the first picture you can see that the RPMs of the Pump are 2500