The Corsair User Forums  

Go Back   The Corsair User Forums > Corsair Product Discussion > Cooling

Reply
 
Thread Tools Search this Thread Rate Thread Display Modes
  #1  
Old 04-15-2018, 06:28 PM
bigdoguk's Avatar
bigdoguk bigdoguk is offline
Registered User
 
Join Date: Aug 2013
Posts: 163
POST ID # = 950448
bigdoguk Reputation: 10
Default H150 i problem

Ok just built my new rig in my 570X with the following corsair parts.

Corsair H150 i
3 ML RGB 120mm (Push)
3 Stock fans that come with the H150 i (Pull)

2 ML RGB 120mm (Top case Push)

1 ML RGB 120mm (Rear Exhaust)

I've used the RGB Light hub that come with the case and commander pro to control the 6 ML RGB fans,all of these run fine and show up on corsair link,the problem I do have is the H150i lights up and the 3 stock fans work but it will not show up in the corsair link at all.
As soon as I installed link yesterday there was a update for it and a firmware so I did that and restarted my pc and the H150i would not show up,I've gone into windows to see if the Corsair USBXp driver was disabled but that was not there it did say generic USB device.

It's late now so I'll try a older version of corsair link tomorrow and see how it goes from there.
Reply With Quote


  #2  
Old 04-16-2018, 10:44 AM
c-attack c-attack is offline
Registered User
c-attack's PC Specs
 
Join Date: Jun 2014
Posts: 5,109
POST ID # = 950536
c-attack Reputation: 84
Default

I think you will have to use 4.9.5.xx or 4.9.6.xx. The 4.9.6 version can be troublesome for the two PRO coolers.

I know we have been talking about this. Is this a Z370 system? Board make and model may have some bearing on the solution. You might also try iCUE. I have found that cleans up some old issues, although it is still a work in progress.

Last edited by c-attack; 04-16-2018 at 10:51 AM.
Reply With Quote


  #3  
Old 04-16-2018, 11:01 AM
bigdoguk's Avatar
bigdoguk bigdoguk is offline
Registered User
 
Join Date: Aug 2013
Posts: 163
POST ID # = 950541
bigdoguk Reputation: 10
Default

So far I've tryed all the link software on the site and still no joy,will not show the H150i at all although the pump RGB and stock fans are spinning.
Windows 10 shows the software is there but it's coming up as a generic USB device.

ASUS Maximus x formula coffee lake motherboard
8700k cpu
This motherboard only has one internal USB conecter .
Tryed ICUE. Same as link no H150i showing up everything else is.
Reply With Quote


  #4  
Old 04-16-2018, 11:07 AM
c-attack c-attack is offline
Registered User
c-attack's PC Specs
 
Join Date: Jun 2014
Posts: 5,109
POST ID # = 950542
c-attack Reputation: 84
Default

Hmm... that is interesting. I would think my Code and your Formula would have the same USB arrangements and behavior. My H115i PRO has been the least fussy of any Corsair Link cooler I've owned. I think we Dev or one of the more savvy software folks to aid. You can try the usual work arounds like running a mini to B connector to the back, but obviously that is not an acceptable long term solution.

Windows version (winver)?
Reply With Quote


  #5  
Old 04-16-2018, 11:16 AM
DevBiker's Avatar
DevBiker DevBiker is offline
iCue βeta Team Green
DevBiker's PC Specs
 
Join Date: Feb 2017
Location: Republic of Texas
Posts: 2,760
POST ID # = 950543
DevBiker Reputation: 57
Default

Have you taken a look at what USBDeView sees? This should give us the VID (1b1c) and PID (0c13).

What are your BIOS settings for Legacy USB Support and XHCI Handoff?

As c-attack mentioned, an alternative is to use a standard micro-USB cable and route it to a port in the back of the motherboard. If this works, then we are either looking at an issue with your USB port or an issue with the cable. Of the two, I would think that cable is more likely. If it doesn't work ... well, we still need to figure things out. Note, also, that iCue has a Drivers folder (C:\Program Files (x86)\Corsair\Corsair Utility Engine\driver) where you can manually install the driver. It's in the siusbxp folder.
__________________
PSA: Please click "Edit System Specs" and fill out your system info.
This comment is provided "as-is", without warranty of any kind, express or implied, including, but not limited to, the sanity or mental fitness of the author.

Reply With Quote


  #6  
Old 04-16-2018, 03:32 PM
bigdoguk's Avatar
bigdoguk bigdoguk is offline
Registered User
 
Join Date: Aug 2013
Posts: 163
POST ID # = 950602
bigdoguk Reputation: 10
Default

Bit of a funny one now as I pluged in the H150i to the motherboard usb and it showed in link then plugged it back into cp and its gone.
Legacy usb is on auto.
Usbd sees the H150i but its not connected.

Tried iCUE same problem as link




Reply With Quote


  #7  
Old 04-19-2018, 06:31 AM
bigdoguk's Avatar
bigdoguk bigdoguk is offline
Registered User
 
Join Date: Aug 2013
Posts: 163
POST ID # = 951079
bigdoguk Reputation: 10
Default



All sorted now fresh install of windows 10 and bios update :)
Thanks for the help lads.
Reply With Quote


Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:12 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.