Yellowbeard Posted April 5, 2011 Share Posted April 5, 2011 In the past, users have used a manual registry tweak to enable the system to load Windows after changing from IDE to AHCI mode. The only other option was to reload the OS with the drive in AHCI mode and load the proper driver. Apparently this little tool has been out since AUG of 2010. It's an AUTOMATED SCRIPT FROM MICROSOFT TO MAKE THE REGISTRY CHANGE. ::pirate:: Link to comment Share on other sites More sharing options...
rajKennedy Posted April 11, 2011 Share Posted April 11, 2011 Will this fix the issue of changing it first in the BIOS? Per Corsair SSD instruction, I changed to AHCI from IDE for better performance (my Performace 3 Series 128) is only getting Sata 3 gp/s speeds, and appears such in Speccy). However, when i change it to AHCI mode i cannot boot. Link to comment Share on other sites More sharing options...
Yellowbeard Posted April 11, 2011 Author Share Posted April 11, 2011 Yes, it should. That is what it is intended to do for Vista and WIN7 users. Run the app, then reboot, set to AHCI. As with ANY operation involving your drives and data, I suggest a backup before doing this. Link to comment Share on other sites More sharing options...
rajKennedy Posted April 12, 2011 Share Posted April 12, 2011 Well Yellowbeard I can't thank you enough for the forthwith reply. I am now getting almost 410/210! Thanks very much- I appreciate it. Go Corsair. Link to comment Share on other sites More sharing options...
Yellowbeard Posted April 12, 2011 Author Share Posted April 12, 2011 Glad to help. There is a manual way to do that but helpful member at the Anandtech forums posted that last week so I shared it here. MUCH easier than the manual registry mod. Enjoy your SSD ::pirate:: Link to comment Share on other sites More sharing options...
Mev Posted June 7, 2011 Share Posted June 7, 2011 I've used the Microsoft automated tool and also followed instructions from the other thread but I still cannot find any option for changing from IDE to AHCI mode in my bios, does anyone or has anyone done this on a Striker Extreme mobo ? Link to comment Share on other sites More sharing options...
Yellowbeard Posted June 7, 2011 Author Share Posted June 7, 2011 I've used the Microsoft automated tool and also followed instructions from the other thread but I still cannot find any option for changing from IDE to AHCI mode in my bios, does anyone or has anyone done this on a Striker Extreme mobo ? Check with Nvidia or ASUS but I don't think your chipset supports AHCI. Link to comment Share on other sites More sharing options...
aggieoo7 Posted July 13, 2011 Share Posted July 13, 2011 In the past, users have used a manual registry tweak to enable the system to load Windows after changing from IDE to AHCI mode. The only other option was to reload the OS with the drive in AHCI mode and load the proper driver. Apparently this little tool has been out since AUG of 2010. It's an AUTOMATED SCRIPT FROM MICROSOFT TO MAKE THE REGISTRY CHANGE. ::pirate:: Yellowbeard: I just tried switching as JEFF GRUNDY suggested to AHCI on MSI ECLIPSE with I7 965. I use WD RAPTORS HDDs and was not impressed with what Windows INDEX showed. It dropped my index from 5.9 to 5.2. So, unless I did something wrong, WINDOWS 7 PROffessional drivers all showed in SYSTEM for AHCI but not worth the effort. NOTE I AM NOT USING RAID. ANY COMMENTS . THANKS. Link to comment Share on other sites More sharing options...
x509 Posted July 14, 2011 Share Posted July 14, 2011 I've used the Microsoft automated tool and also followed instructions from the other thread but I still cannot find any option for changing from IDE to AHCI mode in my bios, does anyone or has anyone done this on a Striker Extreme mobo ? Worked for me on an ASUS H55 chipset board. Link to comment Share on other sites More sharing options...
Yellowbeard Posted July 14, 2011 Author Share Posted July 14, 2011 Yellowbeard: I just tried switching as JEFF GRUNDY suggested to AHCI on MSI ECLIPSE with I7 965. I use WD RAPTORS HDDs and was not impressed with what Windows INDEX showed. It dropped my index from 5.9 to 5.2. So, unless I did something wrong, WINDOWS 7 PROffessional drivers all showed in SYSTEM for AHCI but not worth the effort. NOTE I AM NOT USING RAID. ANY COMMENTS . THANKS. I cannot comment on how this may or may not work with another manufacturer's drives. You should check with WD. Link to comment Share on other sites More sharing options...
Einherjar Posted August 12, 2011 Share Posted August 12, 2011 I'm still not able to load Windows with the drive in AHCI mode despite applying this registry fix and also doing it myself (the parameter was already at 0). The only option I have is to to reinstall Windows with the drive in AHCI mode. I've done that but a recent BIOS upgrade reset the changes and now I'm forced back to IDE mode. In any case, having my drive in AHCI mode has still not enabled me to upgrade the FS3 firmware, as I've described here. Link to comment Share on other sites More sharing options...
Yellowbeard Posted November 17, 2011 Author Share Posted November 17, 2011 I have the Force 3 240GB in a 2011 MBP 15" i7. Do I need to install Windows 7 on the SSD in order to update from 1.2? Can I attach to Lenovo W510 via eSATA and update from that machine which is already Windows 7? The best answer is "probably". The only way to know is to try it. I have updated via eSATA but it has to be Intel or AMD eSATA, not some 3rd party chip eSATA. Your controller must also be in AHCI mode. And, yes, you can do the update from the disk while it is running the OS if you want to try it that way. Either is fine and won't harm your disk. Link to comment Share on other sites More sharing options...
restrooms Posted December 10, 2011 Share Posted December 10, 2011 Hi, I've been looking around on ways to enable ahci on my laptop but so far no luck. :( my Specs Specifications: AMD Llano Dual Core A4-3300 8gb DDR3 1333ram 60gig Corsair Force 3 ATI Radeon HD6480G ATI Radeon HD6470M there is no option in the bios to change to AHCI my read and write is only 190 and 70 hwinfo64 can see 6gb/s controller on registry msahci is 0 device manager it's amd sata is there any way to enable ahci to get the max speed.. Link to comment Share on other sites More sharing options...
parsec Posted December 10, 2011 Share Posted December 10, 2011 Yellowbeard: I just tried switching as JEFF GRUNDY suggested to AHCI on MSI ECLIPSE with I7 965. I use WD RAPTORS HDDs and was not impressed with what Windows INDEX showed. It dropped my index from 5.9 to 5.2. So, unless I did something wrong, WINDOWS 7 PROffessional drivers all showed in SYSTEM for AHCI but not worth the effort. NOTE I AM NOT USING RAID. ANY COMMENTS . THANKS. First saying you use "RAPTORS" is a vague statement, there are many models of Raptors, it would help to know which one. Next, AHCI mode, which enables Native Command Queuing (NCQ), among other things, was created to increase the performance of standard HDDs, not SSDs. Of course, the HDD must support AHCI protocols in order to use them, which I would think a newer Raptor HDD would, but I'm not an expert on them. Also, an SSD not used in AHCI mode with an AHCI driver, is my definition of "self-gimped". You have an Intel CPU board, so you should have the X58/ICH10R Intel chipset. Does your board have a Marvell or other SATA interface too? If you're not using the Intel SATA interface, then your change to AHCI may have been on the other chipsets. Or, you changed it on the Intel, but you don't use it. Or the other chipset driver was changed to the Windows AHCI driver (msahci), which does not work as well with it. Windows 7 Professional does not have different drivers, you should be using the Intel IRST (RAID) driver in AHCI mode on the Intel chipset for the best performance. Your boards download page has the Intel Matrix or IRST driver for your board, if you are now in AHCI mode on the Intel chipset, download and install that driver and if it does not perform better, your Raptors must be old. Link to comment Share on other sites More sharing options...
parsec Posted December 10, 2011 Share Posted December 10, 2011 Hi, I've been looking around on ways to enable ahci on my laptop but so far no luck. :( my Specs Specifications: AMD Llano Dual Core A4-3300 8gb DDR3 1333ram 60gig Corsair Force 3 ATI Radeon HD6480G ATI Radeon HD6470M there is no option in the bios to change to AHCI my read and write is only 190 and 70 hwinfo64 can see 6gb/s controller on registry msahci is 0 device manager it's amd sata is there any way to enable ahci to get the max speed.. If AHCI mode for your chipset is not available in your BIOS, then there is nothing you can do about it, sorry to say. Many laptops are like yours, the BIOS is minimal and short of a major BIOS update, nothing can fix this. Link to comment Share on other sites More sharing options...
Dlgwarner Posted February 26, 2012 Share Posted February 26, 2012 I recently upgraded my system to a Gigabyte GA-Z68XP-UD4 with an i7-2600k, Corsair ForceGT 120 GB SSD as my system drive (running Windows 7 Ultimate 64-bit). my files are on a 1TB WD Caviar Black. My problem is that my system will still not boot even after making the registry edit explained in the tutorial. A little background on how I got where I am now might help in figuring things out. My original system was configured as Raid 1 on an Intel DP35DP mobo. My c: partition was for OS and programs. I had separate partitions for photos, music, files, etc. I first built the system with just my HDDs, but the RAID was lost. There was an IADStor error that I didn't bother messing with because I knew I was going to install the SSD as my new system drive. I never set the BIOS to AcHI and it must have defaulted to IDE and windows switched the drivers. I transferred my system partition by taking one of my HDDs and using Partition Wizard to delete all but my c: partition. I used ATI2012 to clone my c: drive onto my SSD. Prior to cloning onto the SSD, I used an elevated command prompt to align the drive to 1024k per the tutorial. I made sure the system booted and all my programs were included and then rebooted with my other HDD from the RAiD that still had my file partitions. Everything worked fine, though my Windows experience score only changed from 5.5-6.5. So the last thing to do was enable ACHI. After creating a complete system backup, I edited my registry to change the MSAchi start value to 0, restarted and entered the BIOS and switched the PCI to ACHI, But the OS won't load. I switched back to IDE and booted. I subsequently tried the Fix It script on Windows Support and I tried using the EZSmart Storage utility from Gigabyte. That doesn't even seem to run. So I'm flummoxed. I really don't want to have to start all over with a fresh install. I have so many apps and plugins... Well, you know. I wanted to run in ACHI for performance and to enable TRIM. Does it really matter? It would be a shame to not utilize the SSD capabilities I paid for. Any help would be greatly appreciated! Link to comment Share on other sites More sharing options...
Toasted Posted February 26, 2012 Share Posted February 26, 2012 To check if TRIM is enabled Start menu> CMD > fsutil behavior query disabledeletenotify DisableDeleteNotify = 1 (disabled) DisableDeleteNotify = 0 (enabled) I don't think it matters a lot, Unless you are deleting a lot of files. Link to comment Share on other sites More sharing options...
lxtwin Posted February 28, 2012 Share Posted February 28, 2012 I was going to upgrade the firmware on my 120 and 240 drives, when I installed Windows 7 I set the controller as RAID so that I could mirror the data disks. I notice that the notes talk about always being in AHCI mode but if I change the BIOS from RAID to AHCI it blue screens. Can I run the upgrade in RAID mode as it is not mentioned anywhere ? Link to comment Share on other sites More sharing options...
Toasted Posted February 28, 2012 Share Posted February 28, 2012 Not sure, But it might update. Since the SSDs are not on a RAID array. Link to comment Share on other sites More sharing options...
D2AWinter Posted March 30, 2012 Share Posted March 30, 2012 I was BSOD befor i found this works now ty Link to comment Share on other sites More sharing options...
parsec Posted March 30, 2012 Share Posted March 30, 2012 For people that have Intel CPU/chipset mother boards, there is no reason for or advantage to changing from RAID mode to AHCI, except when required for updating firmware in a SSD. Intel RAID mode has all the functionality of AHCI mode, such as NCQ and Hot Plugging. Intel provides one SATA chipset driver that works in either RAID or AHCI modes, that is Intel Rapid Storage Technology (IRST), whose driver file name is iaStor. The Intel X79 chipset platform uses the RSTe driver, which is also a RAID or AHCI driver. Intel actually recommends that when installing Windows with the intent to use AHCI mode, to just set the SATA mode to RAID instead. That way if you decide to create a RAID array, you can do so any time, without any mode changing, BSOD issues, which is actually a Windows problem. SSD users may think that if they use RAID mode, they won't get the benefits of the TRIM command. That is true, but only if you create an actual RAID array out of two or more SSDs. The small but very important detail is, if your SATA mode is RAID, and the RAID driver is installed, any SSD (or HDD) that is not part of a RAID array (ie, just a single, normal, drive) will receive the TRIM command just as it would in AHCI mode. Actually, any single drive connected to a SATA controller in RAID mode, is just operating in AHCI mode. When SSDs are part of a RAID array/volume, is the only situation where the TRIM command will not work with them. Intel seems to be fixing the no TRIM for SSDs in RAID volumes (but only for RAID 0 arrays) but if and when that does happen is unknown. The TRIM command, which actually is generated and sent to SSDs from the Windows 7 NTFS file system, does not depend on any SATA mode or SATA driver. It works in IDE, AHCI, or RAID mode, with the exception for RAID volumes, described above. It does not need to be enabled, it is on by default. If you are required to perform a firmware (FW) update in AHCI mode, and have been using RAID mode, there is no need to be concerned about this, it can be done very simply. Don't forget that when using the boot to DOS FW update method, you don't boot your usual copy of Windows, so any SATA mode changes will not affect Windows as long as you prevent it from booting. Have your FW update media ready (disk, USB drive), start or restart the PC and run the UEFI/BIOS. Change the SATA mode to AHCI, and then change the boot order so the FW update media is used first. If you are worried about booting into your OS in AHCI mode, just move your normal boot RAID volume to the bottom of the boot order. Save the changes and exit, but insert the FW update media first. Let the FW update complete, hopefully fine, and restart the PC. Get into the UEFI/BIOS again (DON'T forget this step!), reset your SATA mode to RAID, reset your boot order to the RAID volume, save and exit. You should see the Intel RAID Option ROM run during POST, and verify that all is correct. Keep your finger ready to start the UEFI/BIOS if something is not right. Link to comment Share on other sites More sharing options...
qcx2987 Posted April 3, 2012 Share Posted April 3, 2012 with respect to raid or ide etc, i just ordered a 45 gb Corsair Accelerator SSD drive to use as a cache drive. when i install it do i set the bios as ide or AHCI do want any RAID period and double period. I have a NAS right next to my puter that as a more than a TB and it's on all the time for anyting i need, plus i create a mirror back up from time to time for any restore and also keep some of my key daily files on a cloud so just would like to hear pros and cons of setting it up each way tks in advance Link to comment Share on other sites More sharing options...
Brezman Posted April 4, 2012 Share Posted April 4, 2012 In the past, users have used a manual registry tweak to enable the system to load Windows after changing from IDE to AHCI mode. The only other option was to reload the OS with the drive in AHCI mode and load the proper driver. Apparently this little tool has been out since AUG of 2010. It's an AUTOMATED SCRIPT FROM MICROSOFT TO MAKE THE REGISTRY CHANGE. ::pirate:: I'm not sure about any others but I did my last two OS installs in IDE mode and did the registry tweak.. The first one lasted 4 months then BSOD's.. I thought the drive was the issue so I checked it and it was fine.. The second I couldn't even get all the Windows Updates installed before it was BSODing. My latests OS install I just enabled AHCI in the BIOS prior to installing the OS.. and guess what.. No problems at all. It really makes me wonder if that was the cause of my mysterious BSOD's as the drive has been solid now after doing a fresh install of Windows 7/64bit in AHCI mode rather than in IDE and doing the registry tweak. Link to comment Share on other sites More sharing options...
rumbo Posted July 6, 2012 Share Posted July 6, 2012 In the steps to enable AHCI in the REGEDIT, when I right click the Name column, "modify" is greyed out and I can't click it. I also ran REGEDIT as Administrator. What gives? Link to comment Share on other sites More sharing options...
Toasted Posted July 8, 2012 Share Posted July 8, 2012 Have you tried logging in a administrator account? Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.