Phongskile Posted November 12, 2018 Share Posted November 12, 2018 Hi guys, could anyone point me on how to set the fan speed to 100 percent in icue, i know i was able to do it in the old software but the new software is all preset. thank you Link to comment Share on other sites More sharing options...
DevBiker Posted November 12, 2018 Share Posted November 12, 2018 Create a new performance profile with it set to 100%. See this from my 'iCue for the Link User' series: [ame] [/ame] Link to comment Share on other sites More sharing options...
Phongskile Posted November 12, 2018 Author Share Posted November 12, 2018 thank you for the response Link to comment Share on other sites More sharing options...
Phongskile Posted November 12, 2018 Author Share Posted November 12, 2018 will this work if I create a profile of my h150i Link to comment Share on other sites More sharing options...
DevBiker Posted November 12, 2018 Share Posted November 12, 2018 You can create new performance profiles for any device. Just click the "+" button at the top of the Performance tab and then apply it to the device. There are also iCue Profiles, which are a collection of lighting and performance characteristics. And yes, the settings for the H150i would be a part of the profile. Link to comment Share on other sites More sharing options...
Phongskile Posted November 13, 2018 Author Share Posted November 13, 2018 You can create new performance profiles for any device. Just click the "+" button at the top of the Performance tab and then apply it to the device. There are also iCue Profiles, which are a collection of lighting and performance characteristics. And yes, the settings for the H150i would be a part of the profile. Your a legend thanks champ Link to comment Share on other sites More sharing options...
ISAWHIM Posted November 13, 2018 Share Posted November 13, 2018 Unfortunately, you can only add devices that exist in the program, and not all existing devices in the computer are shown. Devices that exist in the older "LINK" program. Nor is there any easy way to change profiles. You are forced to open the program and navigate through the screens to pick a profile, each time. This software fails for ease of use, function and intuition of operation. Even worse that it asks you to install this WITH the LINK software, but then it has no actual control of that software, for devices that NEED that older software. I can't control my video-cards, my motherboard fans, my power supply. Only, after digging around, did I even figure-out how to control the actual corsair cooler. It's not like these are old devices. "Titan X", "Titan XP" and "Titan V", the Motherboard is the newer x299 OC edition with standard RGB controls and fans, which LINK handles fine, yet "this new software", which should be replacing the older software, doesn't work with anything except Corsair hardware, in my setup. This is useless, it takes control of the cooler, so LINK can't control it. Now I need two individual programs that are bloated, to do simple temperature control and lighting. Link to comment Share on other sites More sharing options...
DevBiker Posted November 13, 2018 Share Posted November 13, 2018 Unfortunately, you can only add devices that exist in the program, and not all existing devices in the computer are shown. Devices that exist in the older "LINK" program. Nor is there any easy way to change profiles. You are forced to open the program and navigate through the screens to pick a profile, each time. This software fails for ease of use, function and intuition of operation. Even worse that it asks you to install this WITH the LINK software, but then it has no actual control of that software, for devices that NEED that older software. I can't control my video-cards, my motherboard fans, my power supply. Only, after digging around, did I even figure-out how to control the actual corsair cooler. It's not like these are old devices. "Titan X", "Titan XP" and "Titan V", the Motherboard is the newer x299 OC edition with standard RGB controls and fans, which LINK handles fine, yet "this new software", which should be replacing the older software, doesn't work with anything except Corsair hardware, in my setup. This is useless, it takes control of the cooler, so LINK can't control it. Now I need two individual programs that are bloated, to do simple temperature control and lighting. So ... let's set some things straight. 1) It doesn't ask you to install it WITH the Link software. Unless you have "legacy" Corsair devices that are only supported in Link, you can uninstall Link. I don't know where you got this misconception. 2) Neither Link nor iCue will control a TitanX, TitanXP, Titan V or anything on the motherboard. They never have. They'll show you sensors from them. In Link, it's up front. WIth iCue, you can see them on the Dashboard if you add the widgets. 3) You don't need two applications UNLESS you have legacy Corsair devices that are only supported in Link (e.g. the Commander Mini). Oh, I already said that. Well, just replying to repeated misinformation. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.