Jump to content
Corsair Community

570X which fans top ??


xldeane

Recommended Posts

Hi Guys,

Im not one to moan but did anyone really plan this case out before it was fabricated??

No PSU shrould-

Cable management (access holes) leaves a lot to be desired.

Circuit board for 3.5 HD on show. Put some spacers between bay and case then HD can be fitted the correct way round.

 

The top of the case... Whats going on ?? Am I missing something ? This case comes with a Control unit to control 6 fans. Its says on the Corsair website..

 

Cooling Layout:

Front: 3 x 120mm or 2 x 140mm

TOP: 2 x 120 /140mm

Rear: 1 x 120mm

 

The Top doesnt quite work out or do I have wrong part fitted ?

Please see below. Both 120mm and 140mm fixing holes line up, but the fans arent even center to top of case ?? Why would you want them fitted off center ?

1219824937_120140out.thumb.JPG.3a518c96bec3e6f5eb33466d4249eb62.JPG

1398768107_140PIST.thumb.JPG.2d7a570363a900ef9a9b7ad19866b95d.JPG

519635648_bothWTF.thumb.JPG.e3dd71b5004c3fc9c89944693b98e984.JPG

788147416_140WTF.thumb.JPG.094409ccec0bcde2332792051c649b68.JPG

640298804_2x140top.thumb.JPG.93e8fad9e6ffb2ca63fdcf47d3710a74.JPG

Link to comment
Share on other sites

Hi Guys,

No PSU shrould-

Cable management (access holes) leaves a lot to be desired.

 

Thank you for your feedback! We'll look into it for future products.

 

Circuit board for 3.5 HD on show. Put some spacers between bay and case then HD can be fitted the correct way round.

 

The reasoning for this was to ensure that the HDDs did not overheat. We designed it so that the cage has the best airflow. We'll see what we can do in future cases.

 

The top of the case... Whats going on ?? Am I missing something ? This case comes with a Control unit to control 6 fans. Its says on the Corsair website..

 

That control unit is to control fan LIGHTING. It controls both SP120 RGB and HD120/HD140 RGB fans. The three button controller is the lighting mode, color change, and mode speed (rate of flashing / transition). This is all covered in the manual.

 

The Top doesnt quite work out or do I have wrong part fitted ?

Please see below. Both 120mm and 140mm fixing holes line up, but the fans arent even center to top of case ?? Why would you want them fitted off center ?

 

The offset is to allow for the fans to fit and to prevent hitting memory. This has been an issue in the past with earlier generation of cases, where if you wanted to have tall ram and a radiator with fans on top, they would get in the way of each other. We fixed that by going with this positioning and allows users the freedom to do both. Yes, we understand this prevent proper alignment with the front fans, but we wanted to give our users more options and the capability to install the components they want. This was a highly requested feature for the past couple of years.

 

If you have any other questions, comments, or concerns, let us know.

Link to comment
Share on other sites

Hi

So why didnt you guys just make the case 15-20mm taller. That would have sorted all this out and the fan / memory situation...wouldnt have been a situation. Or better still, have 2 different cut outs. Similar to the fan holder configeration you have at the moment but have one for a rad to be fitted the other one with central holes for fans ?? You sell them in the shop ???

 

xl....out

Edited by xldeane
Link to comment
Share on other sites

I am extremely disappointed so far in this case, yes it looks gorgeous but when you start to add fans to it, then it turns into a bit of a nightmare. I bought the corsair h115i pump thinking it would fit, one fan does but the other wont as the case is too small, as said before a few more mm would not of hurt and would of rectified this problem. I am just hoping my CPU will be ok with just one fan working. As i have not had the case in use and all the film is still on the glass panels i would still consider sending the case back as I find this unsatisfactory for a case that costs 175 pounds!!!!
Link to comment
Share on other sites

I am extremely disappointed so far in this case, yes it looks gorgeous but when you start to add fans to it, then it turns into a bit of a nightmare. I bought the corsair h115i pump thinking it would fit, one fan does but the other wont as the case is too small, as said before a few more mm would not of hurt and would of rectified this problem. I am just hoping my CPU will be ok with just one fan working. As i have not had the case in use and all the film is still on the glass panels i would still consider sending the case back as I find this unsatisfactory for a case that costs 175 pounds!!!!

 

Where have you installed your radiator? We've installed H115is in our builds with no issues.

 

Post up a picture of your setup.

Link to comment
Share on other sites

I thought I was going to enjoy using this case for a new build, but Im not, I have changed fans twice and still got to figure a way to get my 360 rad fitted to front... I feel some threaded rod coming on...

 

 

 

xl.......out

 

How did you go with your build?

 

As far as I could see you can only put it on the front if you move the front fans to the top & rear.

 

Which is a bit pointless, considering you buy the case to show off the fans at the front.

 

It's a real let down, hopefully they hear our feedback and make changes.

 

Here's my experience, I was quite generous in my review:

https://blog.londrigan.com/gaming-pc/crystal-series-570x-rgb/

Link to comment
Share on other sites

How did you go with your build?

 

As far as I could see you can only put it on the front if you move the front fans to the top & rear.

Which is a bit pointless, considering you buy the case to show off the fans at the front.

It's a real let down, hopefully they hear our feedback and make changes.

Here's my experience, I was quite generous in my review:

https://blog.londrigan.com/gaming-pc/crystal-series-570x-rgb/

Thats a lovely looking machine rig- monkey

 

Im going to mount a 360 rad to front with 3 X HD120 RGB fans to front (Inside). 3 X SP120 on the inside.With the rad in the middle. Rad holes tapped out to 4mm to take the weight, 3mm not strong enough . Loads of room.

 

2 X HD 120 RGB on top (not outside though :). All sucking in fresh air inwards..1 X HD120 RGB on the rear as exhaust fan. PSU inverted sucking from underneath blowing out the rear... Should hold Positive pressure although there are lots of vents between glass and case..Plus positive pressure keeps the dust and crap out...

 

xl....out

Link to comment
Share on other sites

Thats a lovely looking machine rig- monkey

 

Im going to mount a 360 rad to front with 3 X HD120 RGB fans to front (Inside). 3 X SP120 on the inside.With the rad in the middle. Rad holes tapped out to 4mm to take the weight, 3mm not strong enough . Loads of room.

 

2 X HD 120 RGB on top (not outside though :). All sucking in fresh air inwards..1 X HD120 RGB on the rear as exhaust fan. PSU inverted sucking from underneath blowing out the rear... Should hold Positive pressure although there are lots of vents between glass and case..Plus positive pressure keeps the dust and crap out...

 

xl....out

 

I would love to see how you do that. :) I had to install the 240mm radiator front bottom because there was no way (even though it looks like there is plenty of room) to get the tubes beneath the top fans. 22070419_1884071054943009_2118981220_o.thumb.jpg.af275a9187953635b6d3406f860792a9.jpg

Link to comment
Share on other sites

I would love to see how you do that. :) I had to install the 240mm radiator front bottom because there was no way (even though it looks like there is plenty of room) to get the tubes beneath the top fans. [ATTACH]31247[/ATTACH]

 

I have measured it precisely (within 5mm :biggrin:) I can get it in not a problem, just a little bit of adjustment to be made :D: and if that fails ill get my power file out with some 40 grit that can solve any fabrication problem :idea::biggrin::biggrin:

 

 

xl...out

Link to comment
Share on other sites

I have measured it precisely (within 5mm :biggrin:) I can get it in not a problem, just a little bit of adjustment to be made :D: and if that fails ill get my power file out with some 40 grit that can solve any fabrication problem :idea::biggrin::biggrin:

 

 

xl...out

 

I have my fingers crossed and hope it works out for you. I also thought at first it wouldn't be a problem and had my rig planned out this way. It might have worked with a lot of force and with the tubes pressing against the top fans the whole time. Check out the pic, the part where the tubes come out of the radiator are on the same height as the top fans and the tubes are way too stiff to bend them this angle. I mean not without a lot of force on them all the time. Pump.thumb.jpg.485e26bda78115c44b2105091e605dc6.jpg

I really wonder why it's so hard for corsair to just give you a few extra centimeters so you can install everything. I love the look of the case, but the cable managment and installation was a huge pain in the a.

Link to comment
Share on other sites

I have my fingers crossed and hope it works out for you. I also thought at first it wouldn't be a problem and had my rig planned out this way. It might have worked with a lot of force and with the tubes pressing against the top fans the whole time. Check out the pic, the part where the tubes come out of the radiator are on the same height as the top fans and the tubes are way too stiff to bend them this angle. I mean not without a lot of force on them all the time. [ATTACH]31251[/ATTACH]

I really wonder why it's so hard for corsair to just give you a few extra centimeters so you can install everything. I love the look of the case, but the cable managment and installation was a huge pain in the a.

 

:biggrin::biggrin::biggrin::biggrin::biggrin:

Gentlemen... Speedbreaker had me doubting myself so I rigged these up and took some photos.. Its fits with 5-10mm gap, 120 on top Fractal Design S360 Cooling unit

 

Phewww

 

gkzqOJb.jpg

612Oz8N.jpg

mCZZpYB.jpg

4CNzBol.jpg

w7gfC72.jpg

 

xl...out

Link to comment
Share on other sites

Hehe is that coolant I see? Did your cooler get so excited it wee a lil? :P

 

LOL You got me doubting myself.. that was blind panic putting that lot in. Fans are only held in by 2 screws each, I have to take them all out again clean and fit properly :)

 

 

xl....out

Link to comment
Share on other sites

But thats not the end of the story... Yesterday morning I did a quick test run on the Kelvin before I started fitting all the really expensive gear into the case....and the unit leaked from the seal around the Block/pump assembly.. I was horrified. So i called up the people I purchased it from and asked for a RMA... anyway... They dont stock the Kelvins anymore (Prob recalled because they leaked) they only stock the Celsius, so i bought one of those instead.. It wasnt until I got home and did a bit of research that I found out the Rads for the Celsius were bigger and piping was thicker.. Rig-Monkey you might well have won this bet after all. Ill update you tomorrow. Its going to be here in a few hours and ill try and fit it in. Its 8mm taller and that could make all the difference between me being a Happy XL or the whole lot going out of my workshop window...

 

 

xl...out

Link to comment
Share on other sites

Morning Guys. I also mounted my rad in the front to the upper 2 fan mounts push/pull.. HD140's in the top of the case and HD120's push/pull. Fits but deffo a tight squeeze. using 120's in the top of the case would give more room thats for sure..

 

JArbbAF.jpg

Link to comment
Share on other sites

  • 2 months later...
Morning Guys. I also mounted my rad in the front to the upper 2 fan mounts push/pull.. HD140's in the top of the case and HD120's push/pull. Fits but deffo a tight squeeze. using 120's in the top of the case would give more room thats for sure..

 

Nice build! Love how you painted over the silver with red too.

Link to comment
Share on other sites

  • 3 months later...
Anyone from Corsair know if the new 570x Mirrorblack, have 140mm fans centered in the top holes or does it still need 120mm fans to have the fans perfectly in the middle of the holes? Since the topicstarter had problems with that.
Link to comment
Share on other sites

The Fan Location in the Mirror Black is Identical to the normal 570x buddy.. due to the nature of how the 120mm's or 140mm's mount.. the 120mm's are the better 'looking' option still.

 

Same case... Mirror Finish ;).. and of course the VERY desirable RGB logo's

Link to comment
Share on other sites

  • 1 year later...
That would be like Nvidia never updating their drivers in 4 years or Asus not updating bios. People would go crazy. I wouldn't read the review of an initial purchaser of a graphics card or motherboard as the standard after four years you would think everything would be fixed. So that's my point the damn case is 4 years old. I guess that's too much to ask for spending $160 on the case
Link to comment
Share on other sites

×
×
  • Create New...