SolidCrew Posted April 27, 2012 Share Posted April 27, 2012 Hi, I have recently purchased... Corsair Dominator GT 16GB (4x4GB) DDR3 PC3-17000C9 2133MHz Dual/Quad Channel Kit with DHX Pro Connector (CMT16GX3M4X2133C9). Seems to be great ram :) SYSTEM SPEC: Asus Maximus IV Extreme (P67) Intel 2600K @ 4.6Ghz (on water) Corsair 1200 PSU I have all 4 modules installed and I loaded the XMP profile. All settings have been applied correctly. I was wondering if I was able to push this ram any further? Tighter timings to try @ 2133 and also higher Mhz to try? Thanks Link to comment Share on other sites More sharing options...
peanutz94 Posted April 27, 2012 Share Posted April 27, 2012 Basically all you can do is experiment and try on your own. Corsair can not guarantee anything other than the rated timings and speeds printed on each stick. But if you can get more out of them , thats a bonus! Link to comment Share on other sites More sharing options...
SolidCrew Posted April 27, 2012 Author Share Posted April 27, 2012 I'm looking for a recommendation to try. Hopefully Ram Guy will be able to assist with those. Link to comment Share on other sites More sharing options...
SolidCrew Posted April 27, 2012 Author Share Posted April 27, 2012 My current timings are... 9 11 10 27 2T Am I not able to put it on 1T? Also it says on the Corsair page that the SPD settings are... http://www.corsair.com/memory/intel-memory-upgrades/quad-channel-intel-memory-upgrade-kits/dominator-gt-with-dhx-pro-connector-1-5v-16gb-dual-channel-ddr3-memory-kit-cmt16gx3m4x2133c9.html 9-9-9-24 Am I able to use those as the main timings ? if so would that be 1T or 2T? thanks Link to comment Share on other sites More sharing options...
Corsair Employee RAM GUY Posted April 27, 2012 Corsair Employee Share Posted April 27, 2012 I am sorry but I can only support the tested settings that will be printed on the modules. But you can try anything that you like. Just don't go over 1.65 Volts on the memory voltage as it might damage your CPU but the memory can take up to 1.9 Volts. Link to comment Share on other sites More sharing options...
SolidCrew Posted April 28, 2012 Author Share Posted April 28, 2012 I am sorry but I can only support the tested settings that will be printed on the modules. But you can try anything that you like. Just don't go over 1.65 Volts on the memory voltage as it might damage your CPU but the memory can take up to 1.9 Volts. hum! Should this ram be on T2? Is that normal for good quality 2133Mhz Ram? Link to comment Share on other sites More sharing options...
peanutz94 Posted April 28, 2012 Share Posted April 28, 2012 Corsair recommends 2t for best stability on almost all modules. Link to comment Share on other sites More sharing options...
Corsair Employee RAM GUY Posted April 30, 2012 Corsair Employee Share Posted April 30, 2012 Command Rate is not really a memory setting and would be dependant on the make and model of MB and PSU and the specific CPU you have installed. You might look this setting up on http://www.techarp.com/show.aspx?fileID=18 and get a better explanation. Link to comment Share on other sites More sharing options...
Wlada011 Posted May 10, 2012 Share Posted May 10, 2012 I will go on same kit with EVGA Z77FTW. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.