|
|
|||||||
| Register | Forum Rules | Support Ticket System | Members List | Social Groups | Edit System Specs | Search | Today's Posts | Mark Forums Read |
 |
|
|
Thread Tools | Search this Thread | Rate Thread | Display Modes |
|
#61
12-14-2007, 05:26 PM
|
||||
|
||||
Yes you would only Disable Legacy USB when you are running a memory test, other wise leave it enabled.
And when over clocking with this platform once you reach a certain point 280-340Mhz the memory would have to be running in sync with the CPU so the memory would be best at DDR667 with that CPU setting but I would suggest running DDr800 Cas 4 memory as it will allow more timings options to enhance performance.
__________________
Support accounts and tickets can be created at https://support.corsair.com. 
|
|
#62
12-14-2007, 08:52 PM
|
|||
|
|||
|
Quote:
or change mine to ddr800 and lower the timming to 4-4-4-15 ??? 
|
|
#63
12-14-2007, 09:07 PM
|
||||
|
||||
|
No what you have now will run great!
__________________
Support accounts and tickets can be created at https://support.corsair.com.
|
|
#64
12-19-2007, 04:25 PM
|
|||
|
|||
|
Quote:
I just got my HX620 in and working on installing it. It says it comes with only 2 SATA connectors and my board takes 4. I currently have 3 SATA drives to install. So... can I order more sata cables for the HX620 or do I need to upgrade to the TX650? Thanks, Jamie
|
|
#65
12-19-2007, 04:30 PM
|
||||
|
||||
|
No it should have came with 4 S-ATA connectors, please send an email to rma@corsairmemory.com along with a brief explanation and your name address and phone number and they should be bale to send you a set.
__________________
Support accounts and tickets can be created at https://support.corsair.com.
|
|
#67
12-19-2007, 04:57 PM
|
|||
|
|||
|
Quote:
Let me double check the manual. Ok... I seemed to have not noticed the 3 and 2 connectors part per cable (just that I had 2 SATA cables) and I missed reading about the 650mm cable altogether (oops). So here's what I have. - 2 x 800mm SATA connector cable with three SATA connector heads - 1 x 650mm SATA connector cable with two SATA connector heads. So it appears I have 3 SATA cables that I can connected up to 8 SATA drives correct? Thanks again, Jamie
|
|
#68
12-19-2007, 05:07 PM
|
||||
|
||||
|
Yes you should be good to go!
__________________
Support accounts and tickets can be created at https://support.corsair.com.
|
|
#69
12-20-2007, 01:50 AM
|
|||
|
|||
|
Helpppppppppppppp ....
I'm back again ...  well for a week now thing seem to run okie ... but since 2 day ago .. i got a reboot .... so i decide to run prime95 blend test longer ... and every time .. when it get to 7-8 hours the system crash .... i re-run memtest --- 4 pass okie ... OCCT -- run 1/2 hours normal .. and 1 hours just mem it's crash when i'm 23 min left ..... so aparently my system is not as stable as i thought ... what can i do ??? ram = 2x2 4096c5dhx 333x9 = 2999 bus Vcore = 1.325 Front bus overide = 1.3575 MCH\ICH = 1.575 Ref frequency =266 Mem frequency = 667 5-5-5-15 .......... 2.04Volt what can i try next ???
|
|
#70
12-20-2007, 12:31 PM
|
|||
|
|||
|
Here's an update on my first pc build!
I got the HX620 hooked up yesterday and then put the 24 pin in and then the 8 pin cpu power connector in. Well... the case I have is the Antec P182 and the Big Typhoon (BT) is sitting right just below the 8 pin connector on my Intel Bad Axe mb. I proceeded to put the 8-pin through the top/back of the case and connect it without taking out the BT. I had one hand pushing the cable in from behind and the other using a screwdriver to line it up and push it in the socket. After about 20 minutes I almost gave up (ha ha) and I thought I'd have to take the BT out. But then I took a little break... said a prayer... then all of a sudden WHAM... it went right right in place! (HA HA). One question (for those who have an Antec P182 case). The bottom fan. I know some people have taken it out. I was thinking about doing the same. Has anyone here done that and does the case stay cool enough? Thanks! Jamie
|
|
#71
12-20-2007, 12:49 PM
|
||||
|
||||
|
Quote:
|
|
#72
12-20-2007, 01:13 PM
|
|||
|
|||
|
Thanks specmike! I thought about that as well.
I was thinking about going through the sliding door think to the upper chamber to connect my 2 SATA 500 gig drives and the back down to the bottom chamber to the 3rd drive. However, since I'm planning on getting a 4th 500 gig SATA drive I'll probably just run another 3 SATA power connector either up again or perhaps around the side of the fan on the bottom. BTW - what case do you use specmike? My main concerns are quiet & cooling since I use my computers in my project recording studio. I was looking at the Thermaltake Armor with the water cooling system for the next one. Jamie
|
|
#73
12-20-2007, 01:34 PM
|
||||
|
||||
|
The only related case I have used is the Antec P180. I have no idea if the internal layout is like the P182. Does your lower drive bay/fan/PSU area look like this pic?
|
|
#74
12-20-2007, 01:51 PM
|
|||
|
|||
|
Quote:
Actually... I had ordered a P180 but then AFTER I did, discovered the P182 and how it was the next step up (DOH!) But when I received the P180, the back panel and the guts were identical to the P182 even though the finish was a P180 (huh?) So maybe I have a P181 eh?  Jamie
|
|
#75
12-20-2007, 02:09 PM
|
||||
|
||||
|
Quote:
|
|
| Thread Tools | Search this Thread |
| Display Modes | Rate This Thread |
|
|
Reputation: 10
Linear Mode
