Jump to content
Corsair Community

Corsair Force LS SSD 120 Non Responding


esen

Recommended Posts

Hi,

 

I have a Force LS SSD 120 as the main drive in one of my dev laptops. Yesterday the computer stopped responding and could no longer reboot from the drive. The drive appears in BIOS but Live UBUNTU couldn't see or mount it. Bought a USB enclosure today hoping that I could get some more information about what's going on. Still can't mount on Linux or Windows but I get the following from DMESG.

 

[12409.748501] usb 3-1: new SuperSpeed USB device number 4 using xhci_hcd
[12409.770788] usb 3-1: New USB device found, idVendor=1f75, idProduct=0621
[12409.770790] usb 3-1: New USB device strings: Mfr=4, Product=5, SerialNumber=6
[12409.770792] usb 3-1: SerialNumber: 1
[12409.988920] usb-storage 3-1:1.0: USB Mass Storage device detected
[12409.989105] scsi host4: usb-storage 3-1:1.0
[12411.276344] scsi 4:0:0:0: Direct-Access     Corsair  Force LS SSD          PQ: 0 ANSI: 6
[12411.276975] sd 4:0:0:0: Attached scsi generic sg2 type 0
[12411.277214] sd 4:0:0:0: [sdb] 234441648 512-byte logical blocks: (120 GB/112 GiB)
[12411.277591] sd 4:0:0:0: [sdb] Write Protect is off
[12411.277595] sd 4:0:0:0: [sdb] Mode Sense: 3b 00 00 00
[12411.277977] sd 4:0:0:0: [sdb] No Caching mode page found
[12411.277982] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[12447.881393] usb 3-1: Disable of device-initiated U1 failed.
[12453.001548] usb 3-1: Disable of device-initiated U2 failed.
[12460.265686] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[12471.433961] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
[12471.641971] usb 3-1: device not accepting address 4, error -62
[12471.706363] usb 3-1: USB disconnect, device number 4
[12471.725991] sd 4:0:0:0: [sdb] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[12471.725994] sd 4:0:0:0: [sdb] tag#0 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[12471.725996] blk_update_request: I/O error, dev sdb, sector 0
[12471.726001] Buffer I/O error on dev sdb, logical block 0, async page read
[12471.726077] ldm_validate_partition_table(): Disk read failed.
[12471.726092] Dev sdb: unable to read RDB block 0
[12471.726117]  sdb: unable to read partition table
[12471.726325] sd 4:0:0:0: [sdb] Read Capacity(10) failed: Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[12471.726328] sd 4:0:0:0: [sdb] Sense not available.
[12471.726348] sd 4:0:0:0: [sdb] Attached SCSI disk

 

Can anyone shed some light as to what's happening here? Even though it says Attached SCSI Disk I still can't mount it at sdb. I can see it says unable to read partition table and some other errors. Are there any tools I can use to restore the data or should I be looking at taking to a data recovery firm.

 

Thanks.

Link to comment
Share on other sites

While it is a Corsair drive and you have posted here. Unfortunately, as there is data that is needed off the drive, Rather than provide suggestions which could potentially lower the chances of recovering data, It will be best to ask in a specialised data recovery forum or similar.
Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...