The Corsair User Forums  

Go Back   The Corsair User Forums > Search Forums

Showing results 1 to 25 of 7724
Search took 0.37 seconds.
Search: Posts Made By: c-attack
Forum: Cooling 03-24-2019, 01:17 PM
Replies: 4
Views: 43
Posted By c-attack
You certainly should use coolant temp for the...

You certainly should use coolant temp for the radiator fans. The cooler's internal controller will do this automatically and take those 2 fans out of the "blast loop" during boot. No need to have...
Forum: Cooling 03-24-2019, 01:08 PM
Replies: 4
Views: 42
Posted By c-attack
It depends on the control source for the fan. ...

It depends on the control source for the fan. The Commander Pro natively can detect it's own temp sensor probes at all time, software or no. But in order to use temperature sources from other...
Forum: Overclocking and Benchmarking 03-24-2019, 10:48 AM
Replies: 1
Views: 211
Posted By c-attack
Someone has surely already written a lengthy...

Someone has surely already written a lengthy memory overclock tutorial out there for Z390 or in general and I won't try and put one here. However, I am sure you have been searching for help...
Forum: Cooling 03-24-2019, 10:26 AM
Replies: 6
Views: 107
Posted By c-attack
Yeah, I don't like the coolant/CPU difference at...

Yeah, I don't like the coolant/CPU difference at all. It is out of spec for a stock chip and most certainly for a delid. There are no miracles on a 9900K like the 8700/8086, but I have a Silicon...
Forum: Cooling 03-23-2019, 10:30 PM
Replies: 6
Views: 107
Posted By c-attack
Coolant temp max at 37C rules out a dying pump or...

Coolant temp max at 37C rules out a dying pump or some kind flow issue. However, to asses the efficiency of what you’re doing now, you need a start/idle coolant temp pre-load. Your probably around...
Forum: Memory 03-23-2019, 08:17 PM
Replies: 6
Views: 2,121
Posted By c-attack
So you need to hit the MemOK switch to return to...

So you need to hit the MemOK switch to return to the BIOS? It does not cycle around back the "boot error" American Megatrends BIOS "F1" screen on its own? All the shuffling pre-BIOS screen is the...
Forum: Cooling 03-23-2019, 08:00 PM
Replies: 3
Views: 128
Posted By c-attack
I don't think you have air bubbles. It usually...

I don't think you have air bubbles. It usually produces a static-like pop or something similar. I can't quite distinguish the whir from anything else. I would typically describe the pump sound as...
Forum: Cooling 03-23-2019, 07:22 PM
Replies: 3
Views: 128
Posted By c-attack
Definitely a pump and it has the typical CoolIT...

Definitely a pump and it has the typical CoolIT sound. It’s quite loud on the recording, but I don’t know if that is mic proximity or actual loudness. I don’t hear anything abnormal in the tone, but...
Forum: iCUE Software 03-23-2019, 07:15 PM
Replies: 3
Views: 79
Posted By c-attack
Ok. I have seen this and had it happen to me a...

Ok. I have seen this and had it happen to me a few times. It’s annoying, but not intended. Two ways to try and fix it. Quit iCUE. 1) go into the C:User/name/appdata/roaming/Corsair/iCUE folder and...
Forum: Memory 03-23-2019, 03:29 PM
Replies: 6
Views: 2,121
Posted By c-attack
You both are on 9900K and Z390 boards. You may...

You both are on 9900K and Z390 boards. You may want to google around a bit looking for 4000+ MHz speeds and your hardware. There a lot of people struggling with that combination, professionals...
Forum: Cases 03-23-2019, 01:32 PM
Replies: 3
Views: 88
Posted By c-attack
Probably quite a ways past the point where you...

Probably quite a ways past the point where you need an LED light on your case to tell you if the old hard drive is spinning up to "do something". If you are curious about your HDD/SSD activity,...
Forum: iCUE Software 03-23-2019, 09:45 AM
Replies: 5
Views: 99
Posted By c-attack
You only need the Commander Pro if you want iCUE...

You only need the Commander Pro if you want iCUE software control over case fan speed. You will already have this with the cooler fans. The Commander Pro will directly replace the LNP in the...
Forum: Cooling 03-23-2019, 09:19 AM
Replies: 6
Views: 213
Posted By c-attack
If you are hearing anything in a high frequency...

If you are hearing anything in a high frequency range or that changes it's tune with the fan speed, something is wrong. It could be in your power run or it could be the fan. Move the fan to a...
Forum: iCUE Software 03-22-2019, 09:35 PM
Replies: 5
Views: 99
Posted By c-attack
The Lighting Node Pro (LNP) is a lighting...

The Lighting Node Pro (LNP) is a lighting controller. It does not control fan speeds. If you want fan control for your case fans, you need the Commander Pro, which is a LNP + fan controller.

Your...
Forum: Cooling 03-22-2019, 09:16 PM
Replies: 5
Views: 127
Posted By c-attack
OK, unfortunately it is not that simple. You...

OK, unfortunately it is not that simple. You can't just plug in some RGB fans. There are additional hardware requirements. Take a look at the thread below.
...
Forum: Cooling 03-22-2019, 09:10 PM
Replies: 6
Views: 152
Posted By c-attack
On most Asus boards, OPT is a copycat of CPU with...

On most Asus boards, OPT is a copycat of CPU with no settings of it's own. If you put the cooler on CPU fan, you don't want anything else on OPT. CPU/OPT really only has value as twin CPU fan...
Forum: Cooling 03-22-2019, 06:53 PM
Replies: 5
Views: 127
Posted By c-attack
For the Pro series coolers, you can use and PWM...

For the Pro series coolers, you can use and PWM 140mm fan. Both the HD and LL140 will work fine. However, do note you must enter into the RGB control game and will need a Lighting Node Pro and RGB...
Forum: Cases 03-22-2019, 06:37 PM
Replies: 4
Views: 114
Posted By c-attack
Airflow and static pressure are both RPM...

Airflow and static pressure are both RPM dependent. You must run that white LL fan at 2200 rpm to get those values, a pretty substantial noise difference to the ML-Quiet or ML-RGB at 1600. ...
Forum: iCUE Software 03-22-2019, 06:20 AM
Replies: 3
Views: 79
Posted By c-attack
#2 is the current state. I am not sure why that...

#2 is the current state. I am not sure why that is not happening for you. Make sure you don’t stack the top of the queue with HW or assigned profiles. Can you elaborate a bit as to what’s happening? ...
Forum: Cooling 03-22-2019, 05:59 AM
Replies: 3
Views: 102
Posted By c-attack
No, the heat transfer from CPU to cold plate to...

No, the heat transfer from CPU to cold plate to coolant stream is direct contact type. It would be like expecting the heating element on your stove to be the same temperature as the water in the pot...
Forum: Cooling 03-21-2019, 08:54 PM
Replies: 18
Views: 272
Posted By c-attack
I don’t like your coolant temperature either. The...

I don’t like your coolant temperature either. The ambient to idle temp difference is higher than my load levels. Is there any kind restriction that might affect the radiator? A R6 front intake mount...
Forum: Cooling 03-21-2019, 06:59 PM
Replies: 27
Views: 630
Posted By c-attack
You will hit the cpu limit long before you reach...

You will hit the cpu limit long before you reach a physical temperature limit on the rubber and metal. Most manufacturers list 55-70C as a coolant limit. Anytime you reach 50C you should ask...
Forum: iCUE Software 03-21-2019, 05:54 PM
Replies: 1
Views: 76
Posted By c-attack
Can you be very specific about the model/variant?...

Can you be very specific about the model/variant? The method is different.

K95 (18 G-keys) or K95 Platinum (6 G-keys)?

M65...
Forum: Cooling 03-21-2019, 05:49 PM
Replies: 27
Views: 630
Posted By c-attack
Since the temperature change is not actual, there...

Since the temperature change is not actual, there is no need to be alarmed. However, it does make using the three preset curves a bit pointless. Even without this issue, I encourage everyone to...
Forum: Keyboards and Mice 03-20-2019, 08:11 PM
Replies: 1
Views: 87
Posted By c-attack
Put that slide button right back in the middle of...

Put that slide button right back in the middle of the line to restore balance. That slider button is heavy shift up or down and it is generally preferable and more precise to change the DPI values...
Showing results 1 to 25 of 7724

 
Forum Jump

All times are GMT -4. The time now is 04:11 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.