The Corsair User Forums  

Go Back   The Corsair User Forums > Search Forums

Showing results 1 to 25 of 7704
Search took 0.39 seconds.
Search: Posts Made By: c-attack
Forum: Cooling 03-21-2019, 08:54 PM
Replies: 15
Views: 153
Posted By c-attack
I don’t like your coolant temperature either. The...

I don’t like your coolant temperature either. The ambient to idle temp difference is higher than my load levels. Is there any kind restriction that might affect the radiator? A R6 front intake mount...
Forum: Cooling 03-21-2019, 06:59 PM
Replies: 24
Views: 523
Posted By c-attack
You will hit the cpu limit long before you reach...

You will hit the cpu limit long before you reach a physical temperature limit on the rubber and metal. Most manufacturers list 55-70C as a coolant limit. Anytime you reach 50C you should ask...
Forum: iCUE Software 03-21-2019, 05:54 PM
Replies: 1
Views: 44
Posted By c-attack
Can you be very specific about the model/variant?...

Can you be very specific about the model/variant? The method is different.

K95 (18 G-keys) or K95 Platinum (6 G-keys)?

M65...
Forum: Cooling 03-21-2019, 05:49 PM
Replies: 24
Views: 523
Posted By c-attack
Since the temperature change is not actual, there...

Since the temperature change is not actual, there is no need to be alarmed. However, it does make using the three preset curves a bit pointless. Even without this issue, I encourage everyone to...
Forum: Keyboards and Mice 03-20-2019, 08:11 PM
Replies: 1
Views: 55
Posted By c-attack
Put that slide button right back in the middle of...

Put that slide button right back in the middle of the line to restore balance. That slider button is heavy shift up or down and it is generally preferable and more precise to change the DPI values...
Forum: Keyboards and Mice 03-20-2019, 08:08 PM
Replies: 3
Views: 59
Posted By c-attack
If it was a mouse 6, then it could never be a...

If it was a mouse 6, then it could never be a sniper button. The only way to be both is to program it. The mouse is advertised as sold as an "FPS mouse". The sniper button is part of that. I...
Forum: Memory 03-20-2019, 07:24 PM
Replies: 5
Views: 144
Posted By c-attack
With XMP off, you will need to manually set both...

With XMP off, you will need to manually set both frequency (3000) and the RAM voltage 1.35v. With XMP disabled, I do not know what value your board will assign. It may be exactly the same (the...
Forum: Keyboards and Mice 03-20-2019, 07:19 PM
Replies: 3
Views: 59
Posted By c-attack
The sniper button and your F14 are both...

The sniper button and your F14 are both non-standard keys that do not have an ASCII value. You won't be able to directly bind them to anything in game. You can use the software to substitute map...
Forum: Memory 03-20-2019, 06:16 PM
Replies: 5
Views: 144
Posted By c-attack
OK, that is pretty much in range. Those values...

OK, that is pretty much in range. Those values can be CPU unique, but since it is such a drastic change between on/off and they are close to the expected target values, they may not be the ones to...
Forum: Cooling 03-20-2019, 05:01 PM
Replies: 14
Views: 183
Posted By c-attack
OK, that sounds like a weird BIOS issue and not...

OK, that sounds like a weird BIOS issue and not the panic button. Still, it is interesting. I would go ahead (if you haven't already) and create a support ticket for Corsair through the ticket...
Forum: iCUE Software 03-20-2019, 04:40 PM
Replies: 7
Views: 82
Posted By c-attack
OK, you lost me. So the same physical fan stays...

OK, you lost me. So the same physical fan stays dark, no matter which place you plug it in. RGB Hub 2, slot #1 does work with other fans?
Forum: Cooling 03-20-2019, 04:36 PM
Replies: 14
Views: 183
Posted By c-attack
Keep an eye on this. You get the CPU Boot error...

Keep an eye on this. You get the CPU Boot error when the BIOS does not detect a device (the cooler) on the other end of CPU fan. Usually this is bad and means something has electrically failed on...
Forum: iCUE Software 03-20-2019, 04:13 PM
Replies: 7
Views: 82
Posted By c-attack
7 does not light up, but 8 does? Hmm. These...

7 does not light up, but 8 does? Hmm. These things normally work in series, so the break in chain kills everything after. Swap 7 & 8 on the RGB lighting hub. Does the “new” #7 go dark? Or does it...
Forum: Memory 03-20-2019, 04:06 PM
Replies: 5
Views: 144
Posted By c-attack
3000 MHz isn’t very high, but the combination of...

3000 MHz isn’t very high, but the combination of high cpu + moderate memory oc may have pushed you past the limit. “The freeze” is usually memory related, but there are no certain rules. Enabling XMP...
Forum: iCUE Software 03-20-2019, 02:33 PM
Replies: 7
Views: 82
Posted By c-attack
Which fan does not light up? (1-6, 7-8)

Which fan does not light up? (1-6, 7-8)
Forum: Cooling 03-20-2019, 01:41 PM
Replies: 14
Views: 183
Posted By c-attack
You will never get fan speed reading in the BIOS...

You will never get fan speed reading in the BIOS for the cooler powered fans. The controller in the pump does not report it to the BIOS, only iCUE/Link. It does report half the pump speed. Other...
Forum: Keyboards and Mice 03-20-2019, 01:30 PM
Replies: 1
Views: 69
Posted By c-attack
The G-keys do exist in the ASCII world, so games...

The G-keys do exist in the ASCII world, so games will not natively recognize the key. You must program G keys and sniper buttons through the iCUE software. The easiest way is by mapping it to an...
Forum: Keyboards and Mice 03-20-2019, 01:15 PM
Replies: 1
Views: 66
Posted By c-attack
Go into iCUE and click on the Glaive. On the...

Go into iCUE and click on the Glaive. On the left side menu, select Lighting Effects.

The Glaive has three lighting zones (logo, edge, front). You can create the 1-3 lighting effects you want...
Forum: iCUE Software 03-20-2019, 12:18 PM
Replies: 6
Views: 125
Posted By c-attack
b) HDD/SSD widget should work. On a new iCUE...

b) HDD/SSD widget should work. On a new iCUE install, you may need to toggle it off/on then restart iCUE. Add the drives from the Dashboard+ >System Info drop down.
Forum: Cooling 03-20-2019, 11:45 AM
Replies: 13
Views: 195
Posted By c-attack
The RGB Lighting Hub is a serial device. All of...

The RGB Lighting Hub is a serial device. All of the fans must go in lowest number order and you cannot skip ports. For 4 fans, you must use lighting ports 1,2,3,4. If you skip a port, you break the...
Forum: Cooling 03-20-2019, 10:14 AM
Replies: 2
Views: 72
Posted By c-attack
It very well maybe slightly different. White has...

It very well maybe slightly different. White has definite tints and the reproduction of "pure white" is a rather elusive thing. It rarely exists, even in very expensive LEDs like you find in high...
Forum: Cooling 03-20-2019, 10:08 AM
Replies: 14
Views: 183
Posted By c-attack
On the GTX/v2 series coolers, the BIOS will show...

On the GTX/v2 series coolers, the BIOS will show half of the the pump speed on the CPU fan header (or wherever you connected). That ~974 corresponds to half the Quiet mode pump speed of ~1950. It...
Forum: iCUE Software 03-19-2019, 08:13 PM
Replies: 6
Views: 109
Posted By c-attack
You should not need a Lighting Node Pro (LNP) and...

You should not need a Lighting Node Pro (LNP) and a Commander Pro at this point. You will only need to install one or the other. If you want fan speed control for the case fans through iCUE, it has...
Forum: iCUE Software 03-19-2019, 08:06 PM
Replies: 6
Views: 109
Posted By c-attack
If you want desktop based software fan control...

If you want desktop based software fan control through the iCUE software that governs the lighting, you will need a Commander Pro. Otherwise, you use the Lighting Node Pro that comes in the triple...
Forum: Cooling 03-19-2019, 07:27 PM
Replies: 14
Views: 183
Posted By c-attack
Your file isn't available and I am not sure the...

Your file isn't available and I am not sure the logs help most of us. Some basic observation of the iCUE/Link data usually is enough to figure out what's happening.

By default the fan curve for...
Showing results 1 to 25 of 7704

 
Forum Jump

All times are GMT -4. The time now is 01:08 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.