Jump to content

ksj4477

Members
  • Posts

    30
  • Joined

Reputation

10 Good
  1. Mine has the same issues with the colors. I just thought that's how everyone's is. I tend to not use white or yellow often since those are the colors you see it in most. I have the CMW16GX4M2C3200C16 and the lighting enhancement kit.
  2. The Z270 board is being controlled in iCUE and seems to be fully controllable at the moment. I didn't tell iCUE to control it or do anything special, after the last iCUE update it showed up in iCUE. It seems like everything is working right so I am going to leave the plugin enabled for now. If it gets weird again I'll disable it. I really hope Corsair is planning on integrating ASUS graphics cards because it would be awesome to control everything through iCUE.
  3. Thanks Dev, I didn't do anything to the software and started my computer this morning, it seemed like Aura was controlling the MB and the graphics card but my Vengeance RGB ram's lighting was frozen. I tried restarting iCUE which didn't help, so I restarted my computer and now everything works as it was supposed to meaning iCUE is controlling everything except the graphics card which is being controlled by Aura. I'd be happy with it if it stayed this way and not randomly do weird things. At some point i'll want different colors and i'll have to open Aura to change the graphics card light and I fear it will go haywire again. I have an older motherboard Maximus Hero IX Z270 so maybe that's an issue too? I didn't iCUE was supposed to run a MB that old?
  4. The last iCue Update it integrated my motherboard without me wanting iCUE to do it. I didn't want to integrate the motherboard because I have an Asus graphics card and I'd rather just control the MB and graphics card in Aura until I can control everything in iCue someday. After the last update I can't control the graphics card light in Aura and it blinks orange. This is annoying. How do I get rid of the MB integration in iCue and hopefully be able to control graphics card light again? Thanks
  5. Yes, they both are configured to 6 LL series fans and 6 RGB strips. I completely removed the LNP and installed the CP in it's place and did the configuration the same. The fans were never even unplugged from the hub, I just unplugged from port 1 on the LNP and plugged it into port 1 on the CP. The configuration has to be correct because I can create a brand new effect and everything lights as I set it so the communication is there. I tried to update the firmware on the CP and it says it's the most current version. The LNP had the newest firmware too.
  6. Yes, my ram and h150i effects come through but the LL fan lighting profiles do not. The CP can see my fans and I can create a new effect so there are no communications issues in that regard. I'm guessing that it sees the LNP and CP as two different devices so it won't just automatically load them. I guess I will reconnect the LNP and just copy the effects as you said. Not quite as easy but easier then trying to recreate some of the effects I have. Thanks!
  7. I figured out how to import and export profiles but importing the profile isn't loading the LNP profiles into the CP. :[pouts:
  8. I think I figured it out. Knowing it exists was half of the battle. LOL Thanks!
  9. Thanks Dev! Is there a tutorial somewhere showing how to do that?
  10. I will be switching from a Lighting Node Pro to a Commander Pro so I can control my fan speeds. I am wondering if I will lose all of my custom fan lighting effects in the process or will they transfer over to the Commander Pro or is there a way I can save them and switch them over? Thanks!
  11. Update: I installed a 470 Ohm resistor on the data wire between the LNP and the lighting strip and it appears to have fixed the issue.
  12. I can get them to work and run the profile I have set in iCUE through the LNP but they periodically start randomly flashing red and blue then they go full white briefly and then go back to the set profile. I believe it’s some sort of interference or ripple in the data feed because if I lightly touch a bare data wire with my finger or the metal of a screwdriver it goes back to working perfectly without glitching. The solder joints all seem to be good so I don’t think it’s a loose connection. I believe it needs a resistor or capacitor on the line but I’m not sure which one or how it should be connected.
  13. So I went for it and they do work fine most of the time but periodically, the LEDs randomly go full white for a minute or so then go back to the regular programming. I'm not sure why they are doing this, when it happens I do notice the first LED in the chain does slightly flicker RGB coloring but the rest are full white. The other weird thing is if I turn the lighting channel off in iCUE, I will see individual LED's flash a random color periodically like they are receiving data from something. It really makes no sense. Has anyone else experienced this?
  14. DevBiker, would I be safe powering this strip directly through a LNP channel or will I need to power this off a separate 5v power source/RGB fan hub? https://www.amazon.com/gp/product/B01MG49QKD If I was to blow the fuse in the LNP, is the fuse replaceable? I am capable of soldering if need be. Thanks!
  15. Any idea when CMWLEKIT2 will be back in stock? I can only find the white kit online.
×
×
  • Create New...