Search the Community
Showing results for tags 'commanderpro'.
Found 16 results
-
I'm trying to connect 20 Corsair fans and would like to control them through icue. 19 Ql120 and 1 Ql140. I'm almost done with the build and ready to install windows but want to be sure I get the wiring right so I don't unintentionally burn something up. Right now i have two thermaltake commander 10 port pwn fan hubs that is sata powered that all my fans are connected to. I'm wondering if i can plug the 4 pin cable going from the thermaltake hub into the corsair commander pro? From looking into this thermaltake hub it sounds like only one fan is detected and the other 9 fans speed is the same as the master fan on the hub. Since it's sata powered i'm assuming it will be safe to plug into the Corsair commander pro. Any help would be greatly appreciated! -
commanderpro Corsair Commander Pro Unstuck
Skylieden posted a topic in Build Hardware Troubleshooting
Greetings! I am new to PC building and this was my first successful build but I am about to transfer from an NZXT case to a Corsair case. I have no idea how to get my commander pro unstuck without breaking it and so this case has just been sitting for over 6 months now and I do want to finally get it out and all put into it. How would you consider getting this module unstuck without essentially damaging it? I don't want to have to buy a new one as they aren't cheap but I also want to get this done ASAP. I heard to use a blowdryer but I am worried it would warp or damage the components inside as electronics don't do well with heat. -
Hallo, ich habe mir gestern einen Corsair Commander Pro besorgt, da mein Mainboard leider nur 2 regelbare Anschlüsse besitzt.. (etwas zu alt 🐵 Angeschlossen und Update gemacht. Alles iO. Nun hab ich meine Lüfter angeschlossen und auch eine Lüfterkurve erstellt. Das Problem ist, dass sich alle Lüfter, egal ob 3 oder 4 Pin genaustens Regeln lassen. Jedoch hab ich 2 Lüfter meiner Kraken X63 WaKü die sich nicht korrekt steuern lassen. Stelle ich den Commander auf 4 Pin und lege eine feste Drehzahl fest, springt die Drehzahl von teilweise 500 bis hin zu 13.000. Auch der Lüfter selbst läuft nicht mit einer konstanten Drehzahl. Ein anderer 4Pin Lüfter am selben port lässt sich jedoch einwandfrei regeln. Der 2. Lüfter der Wakü hat übrigens das selbe Problem. Auch am Mainboard direkt lässt sich der Lüfter einwandfrei Steuern. Sämtliche Programme wie HWInfo usw. sind deinstalliert. Ich kann es mir leider nicht erklären und hoffe auf eure Hilfe. Liebe Grüße Dominik
-
So I bought the 5000t added 2 LL140mm fans and 4 LL 120mm fans on top the three included fnas and rgb strips. I just can't get them all to light up. I have looked up wiring diagrams on how it should be wired and they initially all lit up before the iCue software updated and shut the leds off 2 fans and most of the rgb strips.
-
Fiz a atrualização do icue recentemente e antes estava funcionando tudo normal, porem depois de algum tempo o commander pro nao reconhece na USB, fica como "DISPOSITIVO USB DESCONHECIDO (FALHA NA SOLICITAÇÃO DE DESCRITOR DE DISPOSITIVO" Ai ele não reconhece no icue e nao reconhece o drive, e por esse motivo nao consigo controlar minhas fans, temperaturas, e iluminações.
-
Hello I really hope someone can help me out as I have been trying to figure this issue out for a few days now and nothing. I bought a SP120 RGB pro last week for my new Acer TC-1660-EB11 and connected it through the Lighting Node Pro. The Lighting Node Pro was connected through the provided SATA connection and i plugged the USB directly into the motherboard USB header. The fans spin and the lights work fine but I can't connect the fans or node to the ICue 4 software. I purchased a Commander Pro thinking the Node wasn't working and after installing it was dis appointed to see that ICue still won't detect the Commander or fans. Fixes i have tried are reinstalling, repairing, turning off the quick boot in windows and BIOS, uninstalling the drivers, downloaded USDBeview, playing with the device manager, restarting the box with the pin hole and unplugging/ replugging the SATA. Already sent a ticket to corsair but haven't received a response yet. Nothing has worked and i'm starting to get frustrated I figured spending the 80 dollars on a commander pro would help and am now in the same boat. Is there anything i have missed or any work arounds someone has figured out on here? Edit: also have tried installing ICue 3 with the lighting node but not the Commander Pro. -
Bonjour, Je viens de monter mon premier build, je rencontre un léger problème concernant le système RGB, j'ai installé deux RGB hub sur lesquels j'ai brancher 7 ventilateur, j'ai également un commander pro sur lequel j'alimente 6 des 7 ventilateurs un est branché en direct sur la carte mère, au niveau du RGB je n'arrive pas a synchroniser tout le RGB, lorsque je vais sur icue, il y a parfois le même ventilateur et éclairer sur deux canaux, lorsque je retourne sur le hub il y en a qui s'éteigne, je pense qu'il y a une erreur sur les branchement je n'arrive pas a trouver d'où cela provient, de plus j'ai des ventilateur différent, 6 SP RGB ELITE, et 1 LL120 rgb. Le problème peut-il provenir de cela? Lorsque je vais sur icue il faut indiqué le modèle du ventilateur pour que ca fonctionne je doit les enregistrer sur bande led dans icue sinon ca ne fonctionne pas tres bien. Quelqu'un pourrait peut-être m'aider please?? Merci beaucoup.
-
Bonjour, Je viens ici pour espérer trouver des réponses à mes problèmes car là je suis perdu. En effet, il y a moins d'un an j'ai fait l'acquisition d'un watercooling Corsair H100i elite capellix livré avec son commander pro. Je l'ai monté et je n'ai jamais eu de soucis jusque là. Or, depuis 2 jours j'ai remarqué que les lumières RGB de la pompe du watercooling et de mes ventilateurs ne fonctionnaient plus. Pire encore, la pompe ne marchait carrément plus et 2 de mes ventilateurs ne tournaient plus. Ayant bien suivi comment brancher le Commander Pro voici comment j'ai fait jusqu'alors : Sur le Commander Pro il y a : 5 ventilateurs : 3 ventilateurs de 3 pins et 2 ventilateurs de 4 pins (ce sont ceux de 4 pins qui ne tournent plus) + leur câble RGB. Le branchement de la pompe du watercooling. Le Commander Pro est lui branché en SATA sur mon alim pour l'alimentation et en usb avec son câble intégré directement sur ma carte mère. J'ai tout essayé pour arranger la situation. J'ai changé de branchement SATA, de branchement sur la carte mère, regardé dans le BIOS si la pompe était bien reconnue : rien. J'ai supprimé totalement iCUE y compris dans les clés de registre et je l'ai réinstallé : rien. J'ai essayé de prendre le câble d'un des ventilateurs 4 pins qui ne tourne plus sur le Commander Pro pour le brancher sur la carte mère : il fonctionne normalement cette fois si. J'en ai donc déduis que c'était bien le Commander Pro qui ne fonctionnait plus et je ne sais plus quoi faire là. Le plus étrange c'est que les 3 ventilateurs 3 pins eux fonctionnent sans soucis, sans RGB bien sûr, mais ils tournent. Est-ce que quelqu'un aurait une piste sur ce qu'il se passe ? Est-ce que j'ai bien raison et c'est le Commander Pro qui fait n'importe quoi ou c'est mon PC qui a totalement déréglé le tout...? Même si j'ai des doutes sur la 2ème option vu que j'ai absolument tout supprimé pour réinstaller et rien n'y fait. Merci d'avance !
-
Hello! I have a Commander Pro with 6 LL fans. From 2 or 3 months i can't control the leds of all fans. When i start the pc sometime only one led fan work, sometime 2 and half fans work. When i go in iCUE and change rgb setting (pass from white to red for example) the first fan rest white and the other change color. I tryed to connect the RGB Hub of corsair directly to the Asus Motherboard ARGB connector (data from asus motherboard to the central pin of the hub) and only 4 leds of first fan (i have selected 96 leds int he armoury crate). I restarted the pc reconnecting the HUB to commander pro and only 4 leds of first fan work. Restarted again the pc and 2 and half fans work. I have also disable the plugin and also delete the plugin folder. I'ts like iCue and Armoury Crate share something (memory?). Others have my problem???? I tried also the unistall Armoury crate with Asus tool and clean unistall iCUE (guide on this website) and reistalled all new. Same. How can i solve this problem? -
First of all, early happy August to everyone! So I'm building a new pc since I upgraded my wife's with my old cpu and motherboard and I've run into a strange issue I've never had. Here's a breakdown of all the components : ryzen 5600x (corsair water block) Gigabyte B550 Auros master EVGA 3080 (ek water block) Corsair XD5 EVGA 850 80+ gold psu Lian li o11 dynamic XL 32 gigs of vengeance pro ram at 3600mhz 10 QL 120s 2 commander pros 2 rgb hubs (came with the fans) 2 360s In one hub, I had 4 exhaust fans and the XD5 and their rgb hub. In the other, 6 intake fans and their rgb hub. Both pros plugged into USB ports on the motherboard. So, when I went to fill the system, I noticed that the water wasn't actually moving past the gpu (the run goes pump-gpu- radiator-cpu- radiator- pump), yet all the rgb fans were lit. I thought this was curious. Even more so when I noticed that only the intake fans were actually spinning. So, I pulled the number 6 intake fan, and plugged in the pump. Pump worked. Oh, this is also relevant. The computer was plugged into a strip before. This time, I had to plug it directly into the wall. So, computer filled, ran for 12 hours leak testing. I decide to close everything up and install windows. It cuts on for a brief second, then instantly cuts back off. The rams' rgb is still running, which I'm guessing means there's auxiliary power getting to the board, but not enough to power it. This psu previously ran a 3600, x570 board, same 3080,same hydro x set up, and 8 ML 120s (no rgb). However, only a single pro was used. To troubleshoot, I put it in my wife's computer(3600, x570, H150i, 2 sticks of vengeance at 16 gigs). It powered everything perfectly! So I've narrowed it down to either there's an issue with running 2 pros, or 850 watts isn't enough power. Which is baffling! I have a 1000 watt being delivered tomorrow and will update this thread with my findings. Any suggestions are of course welcome! I just made this in case someone else runs into this issue and I get this figured it, it may help someone in the future! TLDR; 850 watt psu worked in old system, doesn't work in new system that has one extra commander pro and 2 extra fans Profuse apologies for the long read!
-
Hi All, I am brand new to the forums here at Corsair and my first time actually going full Corsair for my new pc upgrade. I have a basic question that I need to ask just to be sure it's okay to do so because the last thing I want to do is remove something that could be problematic in the long run. I have recently purchased the new Corsair ICUE 5000X (By the way absolutely in love with it); It comes with a lighting node core pre installed but I am interested in installing my Corsair Commander Pro and I'm wondering if I can remove the pre-installed lighting node core completely from the case? I would appreciate an answer to this question as I am really not sure. Cheers!
-
Hi Ich habe heute ein Setup gebaut verbaut sind eine CommanderPro und 10 LL120 Lüfter, 3davon AIO eigentlich läuft alles nur ein Lüfter lief nur max. 150 RPM dachte der Lüfter sei defekt aber liegt scheinbar an der CommanderPro weil wenn ich ein anderen Lüfter inden Steckplatz mache wo der nur bis 150rpm lief läuft der Lüfter auch nur bis 150 RPM denkt ihr das die CommanderPro defekt ist danke schonmal für die Hilfe.
-
I have 3 LL120s on the front of my case and 3 ML120s in a push/pull config. I have 2 LL140s on the top and an LL120 on the back (obsidian 500d rgb case). I used two fan splitters to connect all 9 of these fans to the commander pro. I have phantek halo lux digitals on my ML120 fans, and am using this adapter: https://www.ebay.com/itm/Corsair-RGB-to-JST-SM-Addressable-RGB-Adapter-/372551535271 I own two RGB fan hubs: one that came with the case and one that came from ebay. I want to connect my 6 fans into one RGB fan hub, the phanteks into the other RGB fan hub, and then connect both those into the two LED connections on the commander pro. Can I do this, or will I need to purchase a lighting node pro and plug it into the USB connection on the commander pro?
-
Hey guys, I know that the commander pro is not supported in the iCUE software for MacOS, but does it really have to show up as a up? because now I'm getting this warning every time I log into macOS https://cdn.discordapp.com/attachments/263798638373896203/657749984375996436/IMG_20191220_170327.jpg https://media.discordapp.net/attachments/263798638373896203/657749394472566784/unknown.png?width=662&height=470
-
I just got my system 3 months ago, i was adding some RGB lighting since the system i order has single fan attached to radiator AIO liquid cooler.I bought a commander pro and a 3 pack of ll120's. the reason i got the com pro was because my MOTHER BOARD only has 4 PWM's for the fans, and 2 of them have being taken up by the cooler and fan. i connected the Corsair Com Pro to a free usb header and connected the 3 ll120 fans to the controller. when i run icue software the fans are running at full speed. i switch to quiet mode and it has no change. i cannot lower the speed on the fans. is it suppose be this loud and high rpms? also a more customizable option so i can lower the speed of the fans. i have attached some images of my motherboard and the setup. my apoligies for sounding like a newb, i havent had a gaming computer since medal of honor allied assault was out. let me know there is anything i can do as i dont want my fans to burn out at the speed they are going.
-
Planning to purchase an Asus Z390i for my secondary build. I have a couple questions regarding corsair controller compatibility 1.) Can this board run with a commander pro? It has 2 USB 2.0 headers. (CoPro needs a Usb 2.0) to run and as I will be using the corsair H100i RGB SE, that pump will also use up a USB 2.0 header on the board I know the commander pro has 2 internal usb 2.0 ports as well, which leads me to my next question 2.) Can i plug the USB 2.0 from the Pump into the commander pro instead of onto the motherboard? I will be purchasing the LL120's 3 pack as well and that will come with a rgb led hub so the NoPro that comes with it to my understanding is that the CoPro will be the one I use since it does the job of the NoPro and more
