PLAYDOH SILVERSTONE TJ 07 with acrylic tubing and acrylic midplate

PLAYDOH SİLVERSTONE TJ07

PART 1

Worklog Jumbo case İs going to the final with next update..

http://forum.corsair.com/forums/showthread.php?t=131011

It is time to begin to a new worklog.

I dont like conventional Cases. I never use an ATX case.

at least BTX or preferably 90 degre rotated cases(RAVEN01)

I want to do different Cases. This will be a small sample.

By the next worklog TRANSFORMER CASE..you cann see what ı mean.

I named it PLAYDOH SİLVERSTONE TJ07

Becose there arae a lot of TJ07 worklogs .And ı wanted to see TJ 07 as different.

Anew worklog:

At this worklog ı use my old Silverstone TJ07. I call it as PlayDoh of the cases.I want to make 3 different cases from this case.

http://imagizer.imageshack.us/v2/800x600q90/18/zevy.jpg

http://imagizer.imageshack.us/v2/800x600q90/836/g98p.jpg

http://imagizer.imageshack.us/v2/800x600q90/542/f5d8.jpg

First worklog TJ07 V1

http://imagizer.imageshack.us/v2/800x600q90/18/zevy.jpg

What I want to achieve are:

To combine front panel with the side window.

To install liquid cooling and achieving this via acrylic pipe.

To use a special distributor for water distribution as midplate.

To enlarge the case for radiators since it is not wide enough.

To stick some parts into the case to obtain a dynamic view

http://imagizer.imageshack.us/v2/800x600q90/593/fr06.jpg

http://imagizer.imageshack.us/v2/800x600q90/138/hg74.jpg

http://imagizer.imageshack.us/v2/800x600q90/837/xxpb.jpg

first 5.25 rotated

http://imagizer.imageshack.us/v2/800x600q90/600/p8bq.jpg

made a window at middileplate for water distributor

http://imagizer.imageshack.us/v2/800x600q90/31/cwfa.jpg

http://imagizer.imageshack.us/v2/800x600q90/36/h53f.jpg

two 80 mm fan holes are used for pump and tops

http://imagizer.imageshack.us/v2/800x600q90/35/z3w5.jpg

The tops mounted on an alu plate

http://imagizer.imageshack.us/v2/800x600q90/837/44uk.jpg

http://imagizer.imageshack.us/v2/800x600q90/268/egtc.jpg

and the plate with tops mounted to the case

http://imagizer.imageshack.us/v2/800x600q90/12/lbci.jpg

http://imagizer.imageshack.us/v2/800x600q90/12/qbqw.jpg

The pumps with modkit are sticked to the backpanel

http://imagizer.imageshack.us/v2/800x600q90/13/24f6.jpg

http://imagizer.imageshack.us/v2/800x600q90/823/17bk.jpg

OTHER WORKLOGS

MMT 900 D Case

http://forum.corsair.com/forums/showthread.php?t=130728

ER36PO Thermaltake Level 10 GT Snow Edition Case

http://forum.corsair.com/forums/showthread.php?t=130848

12 Angry Men 900 D Case

http://forum.corsair.com/forums/showthread.php?t=130939

4Way HDD Switcher

http://forum.corsair.com/forums/showthread.php?t=131284

How to make a BENCH CASE from an old ATX case

http://forum.corsair.com/forums/showthread.php?t=131089

JUMBO CASE

http://forum.corsair.com/forums/showthread.php?t=131011

Graphic Equalizer Display

http://forum.corsair.com/forums/showthread.php?t=133084

TRANSFORMER CASE

http://forum.corsair.com/forums/showthread.php?t=132019

Update 23/08/2014

To mount PSU ı made a window at the top.

http://imagizer.imageshack.us/v2/800x600q90/15/0ndd.jpg

Made a mounting kit to mount psu.

http://imagizer.imageshack.us/v2/800x600q90/31/ao8j.jpg

http://imagizer.imageshack.us/v2/800x600q90/59/ffzw.jpg

http://imagizer.imageshack.us/v2/800x600q90/33/v62z.jpg

http://imagizer.imageshack.us/v2/800x600q90/12/xb4b.jpg

http://imagizer.imageshack.us/v2/800x600q90/59/yenk.jpg

http://imagizer.imageshack.us/v2/800x600q90/823/5ykk.jpg

http://imagizer.imageshack.us/v2/800x600q90/845/i7ke.jpg

To cover the hole spaces around MB made these parts with gromets.

http://imagizer.imageshack.us/v2/800x600q90/856/hjt5.jpg

http://imagizer.imageshack.us/v2/800x600q90/43/nsbv.jpg

http://imagizer.imageshack.us/v2/800x600q90/713/kay9.jpg

http://imagizer.imageshack.us/v2/800x600q90/577/s62q.jpg

http://imagizer.imageshack.us/v2/800x600q90/31/5qcv.jpg

made 2 X360 Rad stands for rad mounting

http://imagizer.imageshack.us/v2/800x600q90/19/0anu.jpg

http://imagizer.imageshack.us/v2/800x600q90/199/f8u4.jpg

http://imagizer.imageshack.us/v2/800x600q90/202/afpa.jpg

http://imagizer.imageshack.us/v2/800x600q90/835/zatf.jpg

update 28/08/2014

First meeting with acrylic pipes. I had worked before with glass pipes and Copper pipes.

But Acrylic was differnt. First experiments -how to measure -

http://imagizer.imageshack.us/v2/800x600q90/593/5yeu.jpg

http://imagizer.imageshack.us/v2/800x600q90/40/0p0o.jpg

http://imagizer.imageshack.us/v2/800x600q90/34/1rda.jpg

Some tools to work. A plastic mieter box , a handsaw, and a file for the ends.

and some experiments to bend

http://imagizer.imageshack.us/v2/800x600q90/839/iasn.jpg

http://imagizer.imageshack.us/v2/800x600q90/838/88v8.jpg

http://imagizer.imageshack.us/v2/800x600q90/822/t4bg.jpg

http://imagizer.imageshack.us/v2/800x600q90/716/3jz3.jpg

http://imagizer.imageshack.us/v2/800x600q90/32/flnx.jpg

http://imagizer.imageshack.us/v2/800x600q90/809/t4ua.jpg

http://imagizer.imageshack.us/v2/800x600q90/513/zes6.jpg

http://imagizer.imageshack.us/v2/800x600q90/12/hgdz.jpg

http://imagizer.imageshack.us/v2/800x600q90/543/rtol.jpg

İt was easy to bend L parts, but U and S parts was difficult.

Therefore I made m y bending table.

I can bend with different Radius and bend in 2 and 3 directions

http://imagizer.imageshack.us/v2/800x600q90/268/7u40.jpg

http://imagizer.imageshack.us/v2/800x600q90/23/dnoy.jpg

http://imagizer.imageshack.us/v2/800x600q90/543/4vxa.jpg

http://imagizer.imageshack.us/v2/800x600q90/34/8yge.jpg

http://imagizer.imageshack.us/v2/800x600q90/69/mrmh.jpg

http://imagizer.imageshack.us/v2/800x600q90/196/7nml.jpg

http://imagizer.imageshack.us/v2/800x600q90/829/u9gy.jpg

http://imagizer.imageshack.us/v2/800x600q90/20/g8mh.jpg

http://imagizer.imageshack.us/v2/800x600q90/23/vsvt.jpg

http://imagizer.imageshack.us/v2/800x600q90/707/8bap.jpg

and first experiments with acrylic pipes.

http://imagizer.imageshack.us/v2/800x600q90/22/gr54.jpg

update 05/09/2014

Fighting with acrylic tube…

http://imagizer.imageshack.us/v2/1280x1024q90/745/wHNNpA.jpg

http://imagizer.imageshack.us/v2/1280x1024q90/673/kxgxgm.jpg

http://imagizer.imageshack.us/v2/1280x1024q90/674/cW82tL.jpg

http://imagizer.imageshack.us/v2/1280x1024q90/673/NylCda.jpg

http://imagizer.imageshack.us/v2/1280x1024q90/538/1CiylG.jpg

I want to make a waterdistrubutor to this place as midplate

http://imagizer.imageshack.us/v2/800x600q90/34/cmfd.jpg

Planning waterdistrubutor

http://imagizer.imageshack.us/v2/1280x1024q90/540/kORVyS.jpg

http://imagizer.imageshack.us/v2/1280x1024q90/674/49B4in.jpg

http://imagizer.imageshack.us/v2/1280x1024q90/540/6ffsEu.jpg

And some pics from acrylics

http://imagizer.imageshack.us/v2/1280x1024q90/537/93WWmP.jpg

http://imagizer.imageshack.us/v2/1280x1024q90/537/Gjhrjz.jpg

http://imagizer.imageshack.us/v2/1280x1024q90/540/MpiW9n.jpg

http://imagizer.imageshack.us/v2/1280x1024q90/905/Dzxppa.jpg

http://imagizer.imageshack.us/v2/1280x1024q90/745/ofuXSG.jpg

update 17/09/2014

I want to make a waterdistrubutor from acrylic to this place as midplate

http://imagizer.imageshack.us/v2/800x600q90/34/cmfd.jpg

Planning water distrubutor with acrylic pipes

http://imagizer.imageshack.us/v2/800x600q90/842/9po7.jpg

And plan of diftrubutor at corel

http://imagizer.imageshack.us/v2/800x600q90/194/ffq4.jpg

You have two ways to cut plexis

1-With CNC Router

http://imagizer.imageshack.us/v2/800x600q90/833/hhlg.jpg

2- with CNC Laser

http://imagizer.imageshack.us/v2/800x600q90/838/oxe7.jpg

I used CNC laser

acrylic sheets from bottom to top.

No 1: 5mm milk White

No:2 10mm clear

No: 3 5mm clear

No: 4 2mm milk white

http://imagizer.imageshack.us/v2/800x600q90/23/3lzh.jpg

http://imagizer.imageshack.us/v2/800x600q90/585/0fqe.jpg

http://imagizer.imageshack.us/v2/800x600q90/542/pde9.jpg

bonding acrylic sheets with cloroform.

http://imagizer.imageshack.us/v2/800x600q90/826/zizi.jpg

dont use bits for metal use bits for wood..

http://imagizer.imageshack.us/v2/800x600q90/853/l31z.jpg

http://imagizer.imageshack.us/v2/800x600q90/853/a2xg.jpg

http://imagizer.imageshack.us/v2/800x600q90/89/jlqc.jpg

http://imagizer.imageshack.us/v2/800x600q90/19/gz8v.jpg

http://imagizer.imageshack.us/v2/800x600q90/547/5cu7.jpg

http://imagizer.imageshack.us/v2/800x600q90/843/9mla.jpg

http://imagizer.imageshack.us/v2/800x600q90/36/gtaa.jpg

UPDATE 02/10/2014

Fans were taken out to enlarge the case for 2x Thermochill 360 rads

I made a radiator shroud for fans and used a phobya 3x rad. Gril.

http://imagizer.imageshack.us/v2/800x600q90/842/alcd.jpg

http://imagizer.imageshack.us/v2/800x600q90/812/80zb.jpg

This was applied on the back cover.

http://imagizer.imageshack.us/v2/800x600q90/21/7nv8.jpg

http://imagizer.imageshack.us/v2/800x600q90/14/e43o.jpg

Covered view of the case.

http://imagizer.imageshack.us/v2/800x600q90/24/ckj6.jpg

http://imagizer.imageshack.us/v2/800x600q90/689/f539.jpg

http://imagizer.imageshack.us/v2/800x600q90/13/qorh.jpg

http://imagizer.imageshack.us/v2/800x600q90/62/2ww3.jpg

http://imagizer.imageshack.us/v2/800x600q90/809/dtwy.jpg

http://imagizer.imageshack.us/v2/800x600q90/843/pgt1.jpg

http://imagizer.imageshack.us/v2/800x600q90/819/djz0.jpg

http://imagizer.imageshack.us/v2/800x600q90/28/hrhs.jpg

http://imagizer.imageshack.us/v2/800x600q90/812/9x21.jpg

http://imagizer.imageshack.us/v2/800x600q90/845/j5s5.jpg

update 23.10.2014

Back cover painted and finished.

http://imagizer.imageshack.us/v2/1024x768q90/401/1z85.jpg

Made a plexi cover for 5.25, that ı not use.,with flash shining theme. illuminated with led.

http://imagizer.imageshack.us/v2/1024x768q90/843/pcyw.jpg

http://imagizer.imageshack.us/v2/1024x768q90/716/gp7u.jpg

http://imagizer.imageshack.us/v2/1024x768q90/829/5x8l.jpg