abn505

Yes I am with my Ryzen 3950X.

After reading your post I decided to take the plunge and my results look good.

Is there a known issue with 13, I am still on 11.3 and don't want to update unless I know. Please Corsair, what has changed and is the updated needed for newer versions of Windows 10?

Thank You!!

Thanks! I was able to find 3.27.68, I was looking for 3.28, but no luck. The one I have fixed it. Thanks

Damn! I don't have the last version on my PC. Do you know a link to old versions?

Updated to 3.29.110 this morning, now my H150I pro doesn't control fans in fixed mode. Quiet, balanced and extreme work. I don't like quiet, fans are too slow, balanced makes my fans run at 100%. I use fixed at 66% give me 1100 rpm, which is perfect for performance and sound. Now the new update I can't control them manually.

I have not tried that. Not sure, but wouldn't that be no better than what I have. I know we are only talking Nano seconds.

I have the same board and memory. I can get it to run 3200, but not with XMP, won't boot. I just set the multiplier at 32 and DDR4 fabric infinity at 1600 and left everything in auto including voltage and timings. The problem I have when trying to set timings 16-18-18-18-36 manually i can't boot. It runs stable at 3200 otherwise, but timings are 22-22-22-53 which sucks. What did you do the get it to run stable?

Can anyone tell me why ICUE is reporting wrong memory timings? It's showing correct speed, but timings are showing 22-22-22-53 for my CMW64GX4M4C3200C16. Thanks

I have a MP600 as a boot drive on a Aorus X570 Master MB with no problems. Like the previous post, try unplugging the other drives then boot and go into BIOS and see if the drive is there. I know some mother boards depending on what slot you put the Nvme drive into disables some SSD ports. Also, if you put operating systems on the other drives, they could be partitioned as boot drives. When installing Windows on a drive it's a good idea to only have that drive installed at the time.

I have the 64gb version on a Aorus X570 Master board and the only way I could get it to run 3200hz was to set memory multiplier to 3200 and DDR4 infinity fabric divider to 1600 for double data memory and leave everything else in Auto. I even keep the timings in Auto as well as the voltage. Make sure to load optimum BIOS settings to clear any remnants of XMP that you may have loaded before doing that.

Okay I have a question. I have been able to run my memory stable it seems a little unconventional to what other people have done. All I did was set the memory multiplier to 32 and set the DDR4 infinity fabric to 1600 and left everything else on AUTO including the voltage which is says in BIOS is 1.2v and the timings are 15-15-15-36, both in auto. I could never get XMP to work. I never get any BSOD. Windows says my memory is running 3200mz and ICUE reports 1600hz which is correct for DDR memory, but it reports the timings at 22-22-22-53. Does anyone know why that is?

I have the same issue with my Corsair Ram on a Aorus X570 Master. I tired XMP, didn't work. Exactly the same issues you had. Called Aorus support, same lady from seven years ago LOL. Solution was to set memory multiplier to 32, for 3200mhz, also in AMD overclocking set the memory DDR and infinity Fabric Frequency/Timing to 1600 for 3200mhz ram since it's duel channel. Leave everything else alone. If you enabled XMP before, make sure to reload BIOS optimal settings before doing this, because XMP that sets RAM timings and even if you have that back in Auto it doesnt work. My memory runs at 3200mhz stable, but they are not the rated timings, so probably not running as efficient as they should be. My memory is CMW64GX4M4C3200C16. Tried setting timings and voltage manually, followed Corsairs instructions, didn't work.

Hey Balo, Yes, it will get tight having to add another lighting node for different fans, guess I will just get LL120's for the top, won't be as pretty. I want to bring more fresh air in the case. My H150i pro is a side mount with LL120 fans blowing out thru the radiator. I could put the fans on the bottom, but the front USB3 cable is really stiff from the case, I would need to get a real flexible USB 3.0 extension cable.