Madmaxneo

I have uninstalled and reinstalled Armory Crate then went through the whole process to get control the MB RGB effects from iCue but the MB no longer shows up in iCue. I went and followed the instructions listed in several of the help videos but nothing works. Both apps are up to date. I have the Asus Plugin installed in iCue I have iCue listed as the top "game" under In Game Lighting Effects. The MB had been in iCue before but now it is not showing up at all.

I know that iCue normally requires Armory Crate to be running for it to work with Asus MB's, but Armory Crate has been using up some serious CPU usage and the longer it runs the worse it gets. I usually notice it when CPU usage is up to 50% but there are times when I don't notice it until it hits 70%. Because of this it looks like I will be needing to uninstall Armory Crate to get my system to run normally, It's not 100% verified that Armory Crate is causing this but on my last scan Armory crate had 8 out of the 10 Powershell processes running that were taking up CPU usage. Is there an alternate way to have iCue control the MB ARGB headers without having to use Armory Crate?

That might work, I'll have to try that when I get the chance. If you consider specific areas with specific colors combined with type lighting with 2 different color effects then yes it is a little complex. The lighting profiles that I downloaded are primarily holiday themed and some do seem complex with the patterns they create with the lighting effects. Thank you!!

As it says. I have a K100 keyboard and I've found some of the fan created lighting profiles fun to use at times. When importing them I make sure the only box that's ticked is the "Lighting Effects" but it still overwrites the macros I've saved in the G keys. If it's not possible to keep the same macros no matter what profile I import, is there a way to use the wheel to switch the only macros in the G keys?

I am trying to do a mural with two or three colors that chase each other or work like a visor, but this seems impossible with the murals. I was able to do it before on an older version of iCue but for some reason now with Murals the options seem limited. The closest I can get with this is with watercolors but I do not want the full spectrum of colors, just two or three. Anyone know how to do this or is it impossible?

I have an old K95 (non RGB) that I would like to give to my nephew. It would be his first mechanical keyboard and he likes the programmable Gkeys. Does the iCue software still support the K95 keyboard on Windows 11?

Then how come the profile was working just fine less than a week ago before I had to reload windows? It was up to date with the latest version of iCue at the time so if it worked then it should work now.

I had to reload Windows onto my machine due to a personal screw up when converting my drive to GPT (my error was the way the MB works)... After getting everything set and reinstalled I tried to import my iCue profile into iCue and it crashes every time and the profile is no where to be found. I have tried both the newest version 3 and the completely new version 4 of iCue but nothing helps. Is there something I am not doing right when importing the profile? Note: Not sure if any of this is important but the profile was created in 2018 and has remained in place since. The profile file name is "Batman & Joker.cueprofile"

The below is all done with the second hub set up using an external 350mm LED strip set on visor. If I connect one Lian Li strip directly to the LNP it works perfectly fine. If I connect the same Lian Li strip to the 1st connection in the 2nd hub and then to the LNP it does not work at all. I removed one of my LL fans from the first hub and ran it through the 1st connection in the 2nd hub and it works perfectly fine (again in the above aforementioned Visor mode).

I'm not entirely sure where to post this question but if I am in the wrong forum please point me to the correct one. I need help in trying to get my additional RGB lighting to work through a second RGB hub. I have one hub with 2 LL140 fans connected to it and that works fine. I purchased a second hub for various aRGB lighting to work along with the required wires (from PirateDog tech on ebay) but so far I have been unable to get any of the aRGB lights to work. I know the second hub works because I connected my LL140 fans to it and they work fine. I was also able to get my aRGB Swiftech Iris fan to light up but have since been unable to get it back up again. Below are the argb lights I have been trying to get to work through this second hub, all of which work fine with the MB lighting controls on a Gigabyte Aorus X570 Elite Wifi board (RGB Fusion). A. Lian Li Lan Cool II case lights with an additional Lian Li light strip B. Swiftech Iris (aRGB) fan C. aRGB lighted GPU support bracket. Note that when I connect the above lights they don't come on at all, which is the same thing that happens with my LL140 fans unless I specifically select the LL fans in the channel they are in. I have been trying to get these lights to work using the "External RGB strip" but it has not been working. I just discovered I can get individual lights to work if I connect them directly to the Node Pro without the RGB hub, yet the LL140 fans work through the hub just fine. How do I get those lights to work with Corsair iCue through the Node Pro using a Corsair RGB hub? On a side but somewhat related question: I have heard that the iCue software has a way of controlling MB lighting. Is it possible for me to do this with my Gigabyte MB? EDIT: I am thinking that the PirateDog Tech wires I got do not work through the RGB hub as they advertise. They work just fine when connected directly to the Node Pro but not when going through the RGB hub. Is there anyone here who can help me rewire the 3 pin connector so it works fine in the 4 pin slot for the Corsair RGB hub?

The idea is that I'd like to combine all of my RGB lighting within my case under one system. I was debating on going with using my MB connectors with a powered RGB light splitter and adapters for the different connectors. My issue is that the MB software (RGB Fusion) isn't anywhere as dynamic as the iCue software is. In the process of talking with some people and ordering 2 Corsair LL 140 fans for my top rad it was mentioned I should control all of my lights through the iCue software because it has some great aRGB control. I agreed as I have the K95 RGB and love the lighting effects. I was wondering if that would be possible and what I might need for some lights to work correctly with iCue. My case lights have the same connectors as my MB and work well. I have a Lian Li Lan Cool II with a Gigabyte Aorus Elite Wifi MB, of which both use a different connector than what the Corsair stuff does. Is there an adapter that would work with those that I could use to connect all the lights to the iCue software. The LL 140 fans I ordered come with a Lighting Node Pro but I can tell it does not have enough ports for all the lights I have currently much less the ones I will be adding with different case (Lian Li O11DXL). I will be adding more RGB fans for the new and larger rad (possibly 2) and probably a couple of the Lian Li light strips and likely one of the aRGB distro plates. Is there a powered hub that will work with the iCue software so I can add more aRGB lights?